Stimmen - 4, Durchschnittliche Bewertung: 5 ( )

Hersteller: Honeywell Dateigröße: 77.38 kb Dateiname: Unterrichtssprache:

MESSAGE CENTER TO: PRESS: Record a message: # + 1 Stop recording before end of 20 seconds: 1 Playback a message: # + 3 Adjust message playback volume: # + 2 + 39 or 6. Mute keypad status announcements: # + 2 + 1 Restore keypad status announcements: # + 2 + 39 or 6. New message indication: If powered by battery, the Message LED will only blink when you activate the keypad by requesting status. If powered by AC, the Message LED will blink continuously. Once the message is played back, the LED will no longer blink. NOTE: If the word “MESSAGE” is annunciated on the 5828V keypad, it means that there is a message waiting at the control panel, which can only be retrieved using the LYNX keypad. To delete a message: Simply record a new message to override the old one. MESSAGE CENTER NOTES . Allow any status annunciation to complete before starting to record your message. . Messages up to 20-seconds long may be recorded and played back at any time. . When messages are first recorded, the red message LED will continuously flash to show that a new message is contained in the message center memory. Once that message is played back, the LED will no longer flash but the message is retained until a new message is recorded over it. . A status announcement will interrupt the recording or playback of a message. If this happens, begin recording or playing the message back again. . If you Mute system status announcements for any reason, you must Restore system status announcements by pressing the keys indicated in the table in order to hear them again. They will not restore on their own. . Recording a message or playing back a stored message is NOT affected by muting. . If you adjust the volume (39 or 6;) when you play back a message, and still want system status announcements to be muted, you must again Mute system status announcements (# + 2 + 1). HOW TO REPLACE THE BATTERIES Keypad wall-mounted: . Grasp the keypad firmly. Lift straight up (about 1/4 inch) and out, to separate the keypad from the mounting plate. This exposes the covered battery compartment on the backside of the keypad. . Rest the inverted keypad on a non-abrasive surface, remove the battery compartment cover and remove the old batteries. When replacing batteries, replace all three with fresh ones and properly discard all the old ones. . Replace the old batteries with 3-AA, 1.5 Volt, Alkaline batteries (ADEMCO part number N7703). Ensure that battery female (-) and male (+) terminals match the embossed battery symbols near the battery receptacle. Replace the battery cover. . Reattach the keypad to its mounting plate by aligning the four mounting holes in the keypad case back with the four mounting clips on the mounting plate. Lower the keypad onto the clips. . After replacing the batteries and reattaching the keypad to the mounting plate, activate the keypad by pressing any numbered key until it beeps. . Enter the following twice: your 4-digit security code + 1 OFF , to clear any trouble condition displayed. GENERAL NOTES . 7K. . FDQQR. E. XVH. D. WK. SULPDU. V\VWH. NH\SDG. '. QR. XV. L. W. WHV. WK. /<1. FRQWUR. SDQHO. WHV. WK. FRQWUR. SDQH. GLUHFWO. IUR. WK. /<1. VHOIFRQWDLQH. NH\SDG. . If the keypad is on battery power, it will shut down in 15-seconds with no key presses, even if exit delay is set to a longer time period. A status check would have to be made to view (or hear) the new status of the security system. . Do NOT use the 5828/5828V to put the Lynx into Speaker Phone mode. . There is no audio indication when you turn on or off lights (X10) using the 5828V. . An RF keypad low battery condition is displayed as, “BAT” and “00” on the 5828/5828V keypad. . Anticipated battery life of the keypad batteries is 1.5 years. . Do NOT use the 5828V for silent panic operation because the keypad itself is not silent. 165 Eileen Way, Syosset, New York 11791 Copyright © 2004 Honeywell International, Inc. . K0021 3/03 Rev. B ...

Herunterladen

Geben Sie zwei Ziffern: