Login:
Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Anleitung Broan, modell NUTONE C501K

Hersteller: Broan
Dateigröße: 79.75 kb
Dateiname:
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


TURN OFF POWER AT SERVICE ENTRANCE BEFORE INSTALLING, WIRING, OR SERVICING THIS PRODUCT. 1. Hold chime mechanism against wall and mark four (4) mounting holes. 2. Drill 3/16” holes where marked and tap in wall anchors from parts bag. 3. Bring wiring through access hole(s) in chime mechanism backplate. 4. Attach chime mechanism to wall with screws from parts bag. Tighten screws securely. 5. Hang chime tubes from mechanism as shown. DO NOT OIL CHIME PLUNGERS. Oil will cause them to stick during operation. If plungers fail to operate freely due to accumulation of dust, cooking grease, etc., clean with a non-flammable cleaning solvent which will evaporate, leaving a dry surface. INSTALLATION (continued) 6. Connect wires to appropriate terminals. RECOMMENDED NEW CONSTRUCTION WIRING F S1 2 3 Front Side Ground 120 Volt AC 16 VAC Transformer Volume ControlNine volt batteries not used R Rear Lighted or Unlighted Buttons NOT USED REPLACING EXISTING 2-NOTE CHIME F S1 2 3 9V 9V Front Side Ground 120 Volt AC 16 VAC Transformer Requires Two 9 Volt Batteries Volume Control R Rear Lighted or Unlighted Buttons NOT USED 7. Install two (2) alkaline 9-volt batteries, if appropriate for your application. Turn on power at service entrance. Make sure pushbuttons operate chime properly. (Adjust switch on circuit board for 4 or 8 chime tones at front door. Side and rear doors will have 1 chime tone each.) 8. Adjust chime volume with stem on circuit board assembly. If plunger(s) fail to strike tube(s), move tube(s) one notch closer. If plunger(s) strike a double tone, move tube(s) one notch out. 9. Hook cover over chime mechanism. 2 SPECIAL MOUNTING INSTRUCTIONS FOR MODEL C500 DOOR CHIME Model C500 may be surface-mounted or recessed into the wall. SURFACE-MOUNTED 1. Remove chime mechanism from wood case. 2. Remove and discard shipping panel from top rear of wood case. 3. Mount and wire chime mechanism. 4. Hang wood case from chime mechanism. 5. Install chime tubes. RECESSED-MOUNTED 1. Cut out a 10-1/2” wide by 59-1/8” high hole in wall centered between two wall studs. 2. Make two mounting frames from 2 x 4’s (Figure 1). 3. Nail mounting frames to wall studs flush with top and bottom of cut-out (Figure 2). 4. Wire chime mechanism. 5. Secure the chime to mounting frames using black screws and finishing washers (Figure 2). 6. Install chime tubes. WARRANTY ONE YEAR LIMITED WARRANTY We warrant to the original consumer purchaser of our products that such products will be free from defects in materials or workmanship for a period of one year from date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one-year period, we will, at our option, repair or replace, without charge, any product or p...

Dieses Handbuch ist für folgende Modelle:
Haustüren und Fenster - NUTONE C500 (79.75 kb)
Haustüren und Fenster - NUTONE C501CY (79.75 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien