Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
4. Even though Auto or Semiauto Clock Set has been performed, the clock is incorrect. • The clock setting data received from the host channel is incorrect. Select a different host channel during Semiauto Clock Set (A page 18), or perform Manual Clock Set (A page 19). 5. “PM” blinks on the front display panel. • The VCR do not work properly. Unplug the AC power plug once, then plug it again. 6. The subtitles and the menu screen are overlapped. • The subtitle display on the TV is set to on. Set it to off. 7. The subtitles cannot be displayed. • You are viewing the program in EE mode through the HDMI connection. Make use of the analog connection (Component Video, S-Video or Video), and set “TV OUTPUT 2” to “ALLto480i” (A page 65). However, if the picture is of 480p image format, the subtitles cannot be displayed. EN 83 The following conditions are product features and do not indicate mechanical problems. Playback of tapes recorded in D-VHS mode • You may see a mosaic (block) noise, grayed images, or a still image in cases of excessive distortion caused when playing back a damaged tape or when the heads are momentarily dirty. • After you press [PLAY (I)], it takes a moment until you see the image and hear the sound. • After you switch playback speeds (when switching from special effect playback to normal playback, for example), it takes a moment until you see the image and hear the sound. For a few seconds, the image may be played back out of sync with the sound. Searching images on D-VHS tapes • The images appear frame by frame. • Block noise may appear on the bottom half of images. • When the blank portion is reached, a still scene of the last recorded image is displayed. The picture stops/There is no sound • When two or more devices are connected to this VCR with the i.LINK cable (a camcorder and another i.LINKcompatible device), do not turn on the camcorder if you record a program from an another i.Linkcompatible device. Turning on and off the camcorder may cause momentary still images and loss of sound. Image or sound is distorted • When recording from a camcorder connected to this VCR with the i.LINK cable, the image or sound may be distorted. If this occurs, insert a D-VHS cassette in the VCR and turn off and on the VCR, then start recording again. If the problem is not fixed, record using the audio/video input connectors instead of i.LINK connector. Recording from camcorders and other devices via i.LINK connector • You may see a mosaic (block) noise. • For scenes with fast action, the image may jitter. This does not affect recording, which will proceed as usual. • When you watch the camcorder’s search images through this VCR, the block noise may appear. • When you record audio-dubbed DVC cassettes (tapes which have four recorded channels), sound may not be heard for the first few seconds. • When you eject and insert D-VHS cassettes, the sound may be interrupted for an instant. • When you press [REC SPEED] to switch recording speed, the sound may be interrupted for an instant. Incorrect image formatting for wide TVs • If you have connected two different devices using the S-video output connectors on the back of the VCR, the sensing signal for wide TVs may not be output correctly depending on the connected devices. If this occurs, use the TV controls to switch the screen size. MOISTURE CONDENSATION Moisture in the air will condense on the VCR when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form on the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the VCR turned on for a few hours to evaporate the moisture before inserting a tape. ABOUT HEAD CLEANING Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or interrupted. Be sure to contact your nearest JVC dealer if such troubles occur. ATTENTION This VCR contains microcomputers. External electronic noise or interference can cause microcomputer to malfunction. If the VCR does not operate correctly switch its power off and unplug the AC power cord from the AC supply. Wait for a while and then plug the power back in. Eject and check the condition of the cassette. If everything appears normal, you can operate the VCR as usual. 84 EN TROUBLESHOOTING (cont.) Error Codes and Messages Some error codes and messages may appear on the TV screen when operating the VCR. Refer to the chart below for the solution. CODE MESSAGE DESCRIPTION 102 “REC PROHIBITED” • An attempt was made to make a D-VHS recording of a program for which only the analog information is copy protected. • While making a D-VHS recording of a program, a signal in which only the analog information is copy protected was input to this VCR. 103 “REC PROHIBITED” • An attempt was made to dub a D-VHS recording of a digitally copy protected program. • While dubbing a D-VHS record...