Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Each press of rt advances/goes back the start time in 1-min. increments. . To advance/go back the start time in 30-min. increments, press and hold rt. 6 Press we to select “STOP”, then press rtto set the desired stop time. . Each press of rtadvances/goes back the stop time in 1-min. increments. . To advance/go back the stop time in 30-min. increments, press and hold rt. 7 Press we to select “DATE”, then press rt to set the desired date. . The current date appears on the TV screen. The date you enter appears in its place. 8 Press we to select “TV PROG”, then press rt to select the desired channel. 9 Press REC MODE to select the desired recording mode. Or press we to select “SP/LP”, then press rt to select the desired recording mode. 10Press the number keys to set “VPS/PDC” to “ON” or “OFF”. * VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this unit. 11 Press ENTER to access the Programme Check screen. 12 Press PROG/CHECK to complete timer programming. “PROGRAM COMPLETED” appears on the TV screen for about 5 seconds, then the normal screen appears. If “PROGRAM OVERLAPPED” appears on the TV screen, see page 58. . To programme another timer, repeat steps 3 – 12. 13 Press VCR TIMER (#) to engage the unit’s timer mode. The VCR timer lamp lights up on the unit and the DVD deck is automatically selected. Press 1 to turn off the unit. When the DVD deck is in timer standby mode, the unit is automatically turned off. . To disengage the timer mode, press VCR TIMER (#) again. NOTES: . To Timer-Record Weekly Or Daily Serials: — anytime during steps 7 through 9, press number key “9” for weekly serials or number key “8” for daily serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the button again makes the corresponding indication disappear. . You can programme this unit to timer-record as many as 8 programmes. If you try to programme the unit to record a ninth, “PROGRAMME FULL” appears on the TV screen. To record the extra programme, you must first cancel any unnecessary programmes. (. pg. 58) . In case of a power failure after programming, the unit’s memory backup keeps your selections for approximately 5 seconds. . Programmes that start after midnight must have the next day’s date. . To record the programmes received by satellite receiver, record on the DVD discs. For details, refer to “Manual Timer Programming” (. pg. 46). PDC Recording Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your unit and have precedence over the advertised times which you may have preset into the timer. This means that your unit will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service in some areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your unit will not start recording if PDC has been selected. Be sure to set PDC to “OFF” if PDC is not available on your selected channel. (See step 7 on page 56.) NOTES: . When you use Manual Timer Programming, set the start time (PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording. . PDC recording is not possible when a satellite receiver or a cable system is connected to L-2 IN/DECODER connector on your unit. . PDC recording is also possible via the L-1 IN/OUT connector. Page 57 April 22, 2004 5:09 pm Filename [DR-MV1SEK_07VCR Operation.fm] Masterpage:Left+ DR-MV1SEK_00.book Page 58 Thursday, April 15, 2004 3:30 PM OPERATIONS ON VCR DECK 58 EN VCR TIMER (#) VCR/DVD CANCEL (&) PROG/CHECK ENTER rtwe 1 4 7 2 5 8 0 3 6 9 1 SAT Check, cancel and change programmes 1 When the VCR timer lamp lights on the unit Press VCR TIMER (#), then press 1. When the VCR lamp does not light up on the unit Press VCR/DVD repeatedly so that the VCR lamp lights up on the unit. 2 Press PROG/CHECK to access the Programme Check screen. To cancel a programme Press CANCEL (&) to cancel a programme. 3 Press rtto select the programme, then press ENTER. The programme screen appears. 4 Change the settings of the desired recording options as required. . Refer to steps 7 – 11 in “Manual Timer Programming” (. pg. 57). 5 Press PROG/CHECK to complete timer correction. The previous screen resumes. 6 Press VCR TIMER (#). . The VCR timer lamp lights up on the unit and the DVD deck is automatically selected. When the DVD deck is in timer standby mode, the unit is automatically turned off. When Progr...