Stimmen - 6, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Check the Owner's Manual provided with each component for the location of SCART socket. Connection to a Satellite Receiver If a Satellite Receiver is used, we recommend the following configuration: SCART-cable (not supplied) Satellite Antenna Satellite Receiver DVD/VCR TV SCART-cable (not supplied) To record from Satellite Receiver press "AUX" on the remote control of DVD/VCR twice. "A2" will appear on the front display. Select the desired TV-program at Satellite Receiver. Connect to a TV with S-Video Output TV DVD/VCR S-Video Cord (not supplied) To Audio (R) Input To S-Video Input To Audio (L) Input S-Video Output Audio (L) Output Audio (R) Output AUDIO Cord (not supplied) Note: • The S-VIDEO jack is useful only for DVD section. • If you use the connection with S-Video Cord, set the "Video Out Select" (P.44) to "Video". Connection to a Decoder (for Premiere Programs) SCART-cable (not supplied) Decoder RF-Output Cable TV- connection TV-unit DVD/VCR SCART-cable (not supplied) Note: Make sure that AV - mode in SYSTEM SETUP - menu has been set to DEC . CLOCK SET SYSTEM SETUP LANGUAGE/SPRACHE/LANGUE AV2 [DEC] SELECT : ENTER :OK MENUEXIT : Playback connection Connect to a Stereo Amplifier with Audio Output If your DVD/VCR is connected to a stereo amplifier, the video soundtrack can output through the loudspeakers of the stereo system. To Audio (L) Input To Audio (R) Input TV AUDIO Cord (not supplied) Stereo Amplifier DVD/VCR Audio (R) Output SCART-cable (not supplied) Audio (L) Output To SCART input SCART-Socket (for TV-RGB/Composite) Connect to an AV Amplifier with built-in digital surround If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems such as Dolby Digital and DTS by using the Coaxial Digital Output. Use this connection to connect an: • AV amplifier with built-in *Dolby Digital decoder • AV amplifier with built-in *DTS decoder SCART-cable (not supplied) To SCART Coaxial digital cable (not supplied) AV Amplifier with built-in various decoder as above DVD/VCR TV Coaxial digital Audio Output SCART-Socket (for TV-RGB/Composite) input Connecting the optical digital cable You may connect to an AV Amplifier with an Optical digital cable (not supplied) instead of a Coaxial digital cable. When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel. When not using the optical digital cable, attach the dust protection cap to protect against dust. NOTES: • The OPTICAL, COAXIAL jacks are useful only for DVD section. VHS signal is output only from the SCART-sockets, AUDIO L/R jacks and RF OUT jack. • When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AV Amplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the speakers to be damaged. • DTS audio will be output only from the COAXIAL output. To hear DTS audio, DTS-Decoder is necessary. When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs. • Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit. Setting the TV to the AV-Channel We recommend that television and DVD/VCR are being connected with a scart cable. In this case, the setting of AV-channel is not necessary. Picture and sound of video cassette will be transmitted to television through the scart cable automatically. Please read the next page. In case of no scart cable connection, you must set the television to the AV- channel. Pay attention to the following notice: A built-in TV-broadcast in DVD/VCR can do the video playback through the supplied antenna cable. This broadcast is sent on UHF, channel 36.To receive this broadcast, you must tune your television to channel 36 in UHF-band.(see step 2) In case a broadcast has already sent to channel 36 in your area or you connect a additional equipment (e.g. Satellite receiver) with a coaxial cable (without a scart cable), you must tune the sending channel in DVD/VCR (see step 3). In your television store the both equipment (the DVD/VCR and the satellite receiver) to 2 different program positions. Example:Your satellite receiver is sent to channel 36. You tune the DVD/VCR to channel 40 (see step 3). (If your DVD/VCR is also sent to channel 36, the interference will occur.) In your television store the channel 36 to e.g. program position 3 and store the channel 40 to e.g. program position 4. Note that the program position 4 must be suitable for video-playback especially. Please see the owner's manual for your television. If the playback picture is often distored, you must select the other program position for DVD/ VCR. Preparation • Turn on the TV. • Make sure the power of DVD/VCR has been turned off. 1 Press the DVD/VCR’s (not the one on your remote control) and keep pressing it until the display shows rF:. The number next to rF: is the channel in UHF-band to which you must tun...