Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
To maximize your enjoyment, please take a few minutes to review this Start Up Guide. It will guide you through all the features and benefits of your new FireBall. If you should need assistance please call our Customer Support Staff at 800.372.4368 INTRODUCTION This FireBall Manual is intended to provide the reader with an overview of the main features and benefits of the Escient FireBall Media Management System. For more detailed instruction and technical information, please refer to the Support section of the Escient web site (DISCLAIMER At the time of printing, the FireBall screenshot images in this manual matched the FireBall interface screens. However, since FireBall has the capability of downloading software updates and enhancements on a regular basis, the resulting screen updates may no longer match the images in this manual. This manual is copyright ©2005 by D&M Holdings and Escient. All rights reserved. WARNINGS AND PRECAUTIONS • Do not use this apparatus near water. • Clean only with a dry cloth. • Do not block any ventilation openings. • Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. • To reduce the risk of electric shock, do not remove the cover. No user serviceable parts are inside. Refer servicing to qualified service personnel. • To prevent electric shock, do not use a 3 wire to 2 wire adapter plug. • A three prong grounded outlet is required. • You are cautioned that any change or modification not expressly approved in this manual or approved in writing by an authorized representative of Escient could void your warranty and/or your authority to operate this equipment. • Prolonged use of any video device which produces a static (non-moving, non-changing) or repetitive image on your projector, television or plasma display device can cause “screen burn-in”. You are encouraged to leave the FireBall screen-saver turned on and set to the lowest possible “time-out” duration. Warning: This device uses the mains plug as the means to disconnect the unit, this unit remains powered unless disconnected from the mains source. SE-D1 START UP GUIDEINSTALLATION1) Unpack the FireBall, cables, and accessories. Install the included batteries into the remote. Write down the FireBall se- rial number (located on the back) here: SERIAL NUMBER: _________________________________ CONTENTS FireBall IR Remote Control (batteries included) Analog Audio/Composite Video Cable (red, white, and yellow) RS-232 Serial Control Cable Ethernet Cable Power Cable Start Up Guide PAGE 1 PAGE 2 SE-D1 START UP GUIDE 2)Follow these steps to connect your Sony CD/DVD changers to your FireBall: 1. Connect one end of the included RS-232 serial cable into Communication Port labeled “Changer”, on the back of your FireBall. 2. Connect the other end of the RS-232 serial cable into the “RS-232C” port on the back of your Sony changer. 3. Locate the Analog Audio (red/white) / Composite Video (yellow) cable that came with your changer. 4. Connect one end of the Analog Audio (red/white) cable into the Analog Audio (red/white) In jacks on the back of your FireBall 5. Connect the other end of the Analog Audio (red/white) cable into the Analog Line Out jacks on the back of your changer. 6. Connect one end of the Composite Video (yellow) into the Composite Video (yellow) In jacks on the back of your FireBall 7. Connect the other end of the Composite Video (yellow) cable into the Video Line Out jacks on the back of your changer. • For the best audio quality, you should also connect a digital optical cable (not included) between your changer and FireBall. • For the best video quality, you should also connnect component video cables (not included) between your changer and FireBall. Note: The RS-232 serial control cable between the FireBall and the changer must be 25 feet or less in length. SE-D1 START UP GUIDE 3) Connect FireBall to your A/V Receiver and TV A)Locate the included Analog Audio/Composite Video Cable. B)Connect FireBall to any available A/V input on your receiver or TV Note: You may use optional s-video or component video cables and optional digital audio cables for the best picture and sound quality. Contact your Escient dealer for more information 4) Connect FireBall to your network using the included Ethernet cable. INTERNET ROUTER PC OR MAC AUDIO IN VIDEO IN TV or A/V Receiver PAGE 3 PAGE 4 SE-D1 START UP GUIDE 5)Connect FireBall to an AC outlet using the included power cord. Note: The power LED on the front of the FireBall will begin to flash. The power LED will turn solid RED once the FireBalll has completed its initialization process indicating the unit is in standby. 6) Press the POWER button on the front panel or on the remote control. The LED will turn solid BLUE and video will be displayed on the TV when the unit is on. Follow the instructions on the screen to complete the setup procedure. SE-D1 START UP GUIDE CODE S...