Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
. Can be used horizontally or vertically. . The drive can write to DVD+R Double Layer discs. . You can write at a maximum of 16x when using high speed DVD+R, DVDR discs. . The drive can write to seven types of disc. . Features the technology to prevent buffer underrun errors. System Requirements The drive should be used with a system that meets the following requirements1). . PC/AT-compatible computer . CPU: Pentium III, 800 MHz or higher (with Nero Vision Express: Pentium 4, 1.6 GHz recommended) . RAM: 256 MB or higher . 1 GB (with Nero Vision Express: 10 GB) free hard disk space . Operating system: Windows 2000 Professional (referred to as Windows 2000), Windows XP Home Edition or Windows XP Professional (referred to as Windows XP) . i.LINK or USB connector 1) The above requirements are the minimum necessary requirements to write to disc normally. Under actual operating conditions, the requirements imposed by your software must also be met. For details, refer to your software documentation. Notes • You must use discs that are compatible with the write speed you have selected. • Writing speed may automatically be adjusted depending on the disc, specified disc speed, or disc conditions such as weight imbalance and eccentricity. • System should meet following requirements in order to use USB 2.0 operation with this device. . Hi-Speed USB (USB 2.0-compliant) interface cable (included). . System equipped with a Hi-Speed USB (USB 2.0-compliant) connector or PCI adapter card, and running the USB 2.0 EHCI device driver1). 1) The USB 2.0 EHCI driver software is supplied with currently available PCI adaptor cards that conform to USB 2.0. You can also use the USB 2.0 EHCI driver software supplied with Windows 2000 SP4 and Windows XP SP1. For details, contact your USB 2.0 adaptor dealer or consult the Microsoft Corporation Web site. • When connected to a product that does not support Hi-Speed USB, the maximum transfer rate is limited to 12 Mbps (equivalent to a USB 1.1 transfer rate). • You cannot use the i.LINK and USB interfaces simultaneously. Introduction 7 Part Names and Functions Front Panel Rear Panel 321 4 5 6 7 8 A Busy indicator Indicates the drive status. Lit (green) : The power is on. Lit (orange): The drive is reading data, playing a music CD, or writing data (packet writing). Blinking (orange): The drive is writing data (disc-at-once or track-atonce). Off: The power is off. B Eject button Press to open and close the disc tray. C Disc tray Insert discs here, label side up. Hint When you insert a disc into the drive, make sure that it is under the four pins. When using the drive vertically, make sure that you set the disc inside the two lower pins. D Power Switch Press to turn the drive on or off. E USB Connector Used with a USB cable to connect the drive to a computer. F i.LINK S400 Connector (6-pin) Used with an i.LINK cable to connect the drive to a computer. G i.LINK S400 Connector (4-pin) Used with an i.LINK cable to connect the drive to a computer. H DC IN Jack Connect the supplied AC power cord to the AC power adapter. Connect this assembly to the DC IN jack, and then connect the whole to the AC outlet. Introduction 9 B Setup Placing the Drive Using the Drive Vertically Attach the supplied stand as illustrated below to use the drive vertically. Position the drive so that the stand straddles the two anti-vibration pads on the drive bottom and then press it into place. Using the Drive Horizontally Place the drive as illustrated below to use the drive horizontally. Connection through i.LINK Note This product including bundled software functions properly under Windows XP, Windows 2000. It may not fulfill all functional and performance specification under other OS (operating system) environment. Before Connection • Refer to the list of contents to verify that the package contents are complete. • If your computer is not equipped with an i.LINK connector, install an i.LINK interface card. • Check the type of i.LINK connector provided with your computer’s i.LINK interface and obtain a compatible i.LINK cable. i.LINK S400 connector (6-pin) i.LINK S400 connector (4-pin) • Have the manual for your computer handy. Installation These instructions apply to most commonly used computers. CAUTION Using the wrong type of cable with this product can cause it to malfunction. Follow the instructions when connecting the product. Setup 11 1 Start your computer. 2 Connect the necessary cables, then turn on the drive. • Connect the i.LINK cable to the 6-pin i.LINK connector on the drive. . For a computer’s 4-pin i.LINK connector : connect to the 6-pin i.LINK connector on the drive. . For a computer’s 6-pin i.LINK connector : connect to the 4-pin i.LINK connector on the drive. • Connect the supplied AC power cord to the supplied AC adapter. Then connect the AC adapter to the drive’s DC IN jack, and connect the power cord to the power outlet. Power Switch i.LINK Cable AC adapter AC power cord 4-pin 4-pin 6-pin 6-pin or Hint ...