Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
• Do not connect your player via your VCR. The image could be distorted by the copy protection system. Terrestrial Antenna connection Connect the Terrestrial TV antenna to the ANTENNA IN jack on the unit. Connect one end of the RF cable to ANTENNA OUT(TO TV) jack on the unit and other end to ANTENNA IN jack on your TV. Passes the signal from the ANTENNA IN jack to your TV/monitor. If you want to use an indoor antenna, use one with a signal amplifier rated at 5V, 100mA and set [Antenna 5V] to [ON] in the setup menu (See page 35). Satellite Antenna connection Connect the Satellite antenna to the RF ANTENNA IN jack on the unit. Connect one end of the RF cable to RF ANTENNA OUT(TO TV) jack on the unit and other end to RF ANTENNA IN jack on your TV. Passes the signal from the RF ANTENNA IN jack to your TV/monitor. Antenna Connection RFRear of this unitRFRFSatellite antennaTVRF CableTVSatellite antennaRear of this unitANTENNARF Cable Installation 15 3 Installation Satellite Setting Once you have completed setting the digital receiver to your individual preferences, you can proceed, if necessary, to adjust the unit settings to your antenna. The menu [Satellite Setting] contains the satellites that have been selected in the installation assistant. If the installation assistant was interrupted, the satellite position [Astra19.2E] is pre-programmed. Should you wish to receive other satellites, or if you are using a different type of LNB, you can adjust your digital receiver to the appropriate data as follows:. Antenna Setting 1. Select [Satellite Setting] option in the [DTV] menu, then press ENTER (). NOTEIf the [DTV Lock] option is set to [Lock], this function is available when you enter the password correctly. (page 34). 2. The [Satellite Setting] menu appear on the screen. Use U/u to select the [Antenna Setting] and then press ENTER (). 3. Use I/i to select a desired particular satellite. 4. Select an item using U/u. If you know the programmed [LNB Frequency], [22kHz Tone], [DiSEqC], [LNB Power], [Transponder] and [Motor], use I/i to select the desired. If you select [DiSEqC 1.2], you can set Motor Driving Mode, Motor Move and Set Limit, and if you select [USALS], you can set the longitude and latitude and use u to select [Go to position]; then motor will move to your selelected satellite as calculating its position. NOTEIf you use USALS, you should know lines of longitude and latitude at your location. 5. Use U/u to select the [Save] and press ENTER () to display the [Saved List] menu. NOTEIf there isn’t LNB Frequency what you want in [LNB Frequency], input LNB Frequency with numerical buttons. 6. Use U/u/I/i to select the [Go To Tuning] and press ENTER (). 7. Select [Start] and press ENTER () to begin the channel search. Use U/u to select a satellite check box and press ENTER () to select or deselect it. You can search All, FREE, CAS channels individually. Press U, you can select Search Type with I/i. All : All channels the satellite searches. FREE: Free of charge channels. CAS(Conditional Access System: Pay channels. Select [Stop] and press ENTER () to stop the channel search. 8. Press ENTER (). NOTEPlease refer to the manuals of your TV, Stereo System or other devices as necessary to make the best connections. Auto Tuning All available satellite TV or radio programmes are searched. 1. Use U/u to select the [Auto Tuning] and press ENTER (). 2. Follow the steps 7-8 from “Antenna Setting” on page 15-16. Manual Tuning All available satellite TV or radio programmes are searched. 1. Use U/u to select the [Manual Tuning] and press ENTER (). 2. Select an item using U/u and If you know the programmed [Satellite], [Frequency], [Polarization], [Symbol Rate], [Modulation], [Network Search] and [Search Type], use I/i to select the desired, Fill the [Frequency] and [Symbol Rate] field using numerical buttons. 3. Select [Start] and press ENTER () to begin the channel search. Select [Stop] and press ENTER () to stop the channel search. 4. Press ENTER (). NOTE• Select [Stop] and press ENTER () to stop the network search. • If you set this option to [On], the unit will search available transponders through network. HDMI Connection If you have a HDMI TV or monitor, you can connect it to this unit using a HDMI cable (Type A, Version 1.3). Connect the HDMI jack on the unit to the HDMI jack on a HDMI compatible TV or monitor. HDMI Connection RFRear of this unitTVRear of this unitHDMI CableTV Set the TV’s source to HDMI (refer to TV’s Owner’s manual). NOTE• If a connected HDMI device does not accept the audio output of the unit, the HDMI device’s audio sound may be distorted or may not output. • When you use HDMI connection, you can change the resolution for the HDMI output. (Refer to “Resolution Setting” on page 19.) • Select the type of video output from the HDMI OUT jack using [HDMI Color Setting] option on the [Setup] menu (see page 37). • Changing the resolution when the connection has already been established may result in mal...