Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
HDMI Cable (not supplied) HDMI-compatible display To HDMI input To HDMI OUT NOTES: • Refer to the owner’s manual for the TV to be connected to this recorder for more information concerning HDMI connections. • HDMI is an evolving technology, so it is possible that some devices may not operate properly with this recorder. •For proper operation, it is recommended that you use as short an HDMI cable as possible. You may not encounter difficulty if you use an HDMI cable that is shorter than 16.4 ft (5m). • Defects in picture and sound quality may occur depending on the quality of the HDMI cables and the nature of the TV set. • No sound will be output from the HDMI OUT jack if the “Digital Output Mode” is not set to “PCM” (see page 27). To select the HDMI output resolution 1. Turn ON the TV and set to the HDMI mode. 2. Press RESOLUTION on the remote control to display the present output resolution. The on-screen display of the output resolution will appear on the upper right of the TV screen for approx. 10 seconds. 3. While displaying the output resolution on-screen, press RESOLUTION. The output resolution will change to the next resolution in the following order. 480p (Progressive) 720p (Progressive) 1080i (Interlace) HDMI NOTES: • When the HDMI cable is connected, the HDMI indicator “HDMI” on the display window will light up. • If the HDMI cable is disconnected, the HDMI indicator “HDMI” on the display window goes off. In this case, connect the HDMI cable again. 18 2K70101A_E P12-19 18 08`02`07, 20:42 Connections with the TV or audio component Connections with the TV or audio component Connect to a stereo amplifier with audio output You can enjoy high quality audio by connecting the audio output to your amplifier. Connect the audio output jacks to any line-level inputs (such as AUX, DVD, CD, etc.) of an audio amplifier. IntroductionTo Audio (R) input Audio cable (not supplied) Audio (R) output To Audio (L) input Audio (L) output Stereo Amplifier DVD/VCR Connect to an AV Amplifier with built-in digital surround If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems such as Dolby Digital and DTS by using the optical or coaxial digital output. Use this connection to connect an: •AV amplifier with built-in *Dolby Digital decoder NOTE: •AV amplifier with built-in *DTS decoder You may connect to a TV with a component video cable (not supplied) or S-Video cable (not supplied) instead of a video cable (not supplied). Audio/Video cable (not supplied) DVD/VCR Video output To Audio/Video input Coaxial digital audio output Coaxial digital cable (not supplied) TV Audio(R) output Audio(L) output Connect either Optical digital cable (not supplied) Optical digital audio output AV Amplifier with built-in various decoder as above Connecting the optical digital cable You may connect to an AV Amplifier with an optical digital cable (not supplied) instead of a coaxial digital cable. When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel. When not using the optical digital cable, attach the dust protection cap to protect against dust. NOTES: • When you connect the recorder to other equipment, be sure to turn off the power and unplug all the equipment from the wall outlet before any connections. •Turn off the amplifier before you connect or disconnect the recorder’s power cord. If you leave the amplifier power on, the speakers may be damaged. • Caution for the optical digital audio output connector: Do not connect to an amplifier (with an optical digital input connector) which does not contain a Dolby Digital or DTS decoder. Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers. • DTS audio will output only from the COAXIAL or OPTICAL output. To hear DTS audio, DTS-Decoder is necessary. • When playing DTS-encoded CDs, only noise will be heard from the speakers or analog stereo outputs. • Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit. • The optical or coaxial digital output jack output sounds in the bitstream. 19 2K70101A_E P12-19 19 08`02`07, 20:42 Various settings SETUP MENU The SETUP MENU consists of several menus where you can make various settings concerning language, audio functions and images. In addition, this menu includes a clock, and other things that require setting just after purchase. For details of each menu, see the corresponding section in this chapter. Using the SETUP MENU The following example shows the basic setting procedure of the SETUP MENU. 1 Press SETUP. The SETUP MENU screen will appear. General A/V Output Timer REC Recording Other 2 Press or to select the desired menu and press ENTER or . The submenu screen of the selected menu will ap- pear. General A/V Output Timer REC Recording Other Language Rating Clock Disc DivX(R) Restore Other OSD DVD Menu DVD Audio DVD Subtitle ...
Dieses Handbuch ist für folgende Modelle:DVD-Player - D-VR600 (7.47 mb)