Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
MARKER : Marks any point during playback. SEARCH : Displays [Marker Search] menu. RANDOM: Plays tracks in random order. Put the battery into the Remote Control Pinch the battery holder clip together then pull the tab to remove the battery holder. Insert the battery with the + facing in the same direction as the + on the battery holder. Replace the battery holder with battery into the Remote Control unit making sure that it is fully inserted. • Replace Remote Control unit battery with 3V micro lithium cells such as CR. 2025 or its equivalent. • Dispose of battery safety in accordance with local laws. Do not dispose of in fire. Warning for replaceable lithium battery • danger of explosion if battery incorrectly replaced. • replace only with the same type battery. • additional warning marking close to the battery if intended to be replaced by users. Warning : The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, incinerate, or heat above 100 °C (212 °F). Replace the battery with Matsushita Elec. Ind. Co., Ltd. (Panasonic), part no. CR. 2025 only. Use of another battery may present a risk of fire or explosion. Dispose of used batteries. Keep batteries away from children. Do not disassemble or dispose of in fire. 5 Power connections Connecting the Power Cable Connect the supplied power cable from the unit to a power socket. Plug into the “DC 12V IN” jack. Attach the power plug to the body of the AC adapter. (The actual set may differ from the drawing.) Power cord release knob Plug into a power source. Right side of the unit AC adapter • This AC adapter operates on 100-240V~ 1A 50/60Hz. • Contact an electrical parts distributor for assistance in selecting a suitable AC plug adapter or AC cord set. • Manufactured by NANJING WANLIDA TECHNOLOGY CO., LTD Connect the Automotive adapter This unit and its automotive adapter are designed for have 8.5-16 volt, negative ground electrical systems. This is standard for most vehicles. If your vehicle has a different type of electrical system, the DC power system cannot be used. Right side of unit Plug into the “DC 12V IN” jack. Plug into the car . s cigarette lighter socket. Automotive adapter • This automotive adapter operates on DC 8.5-16V. • Contact an electrical parts distributor for assistance in selecting a suitable automotive adapter. • Manufactured by NANJING WANLIDA TECHNOLOGY CO., LTD. Caution • To prevent electrical shock and possible damage to your unit or vehicle, always unplug the automotive adapter from the cigarette lighter socket before you remove the plug from your unit. • A 3 amp. 250V fuse for protection is installed in the automotive adapter. • While the engine is being started, disconnect the automotive adapter from the car . s cigarette lighter socket. • Do not operate your unit when the car battery is discharged. Peak current from the car generator may cause the DC fuse to • If the vehicle . s supply voltage drops below approximately 10 volts, your may not work properly. • Do not leave your unit in a place where the temperature (158°F), or the pick-up device may be damaged. Examples include: - Inside a car with the windows closed and in - Near a heating appliance. 6 Hooking up the unit Audio and Video Connection Connect the AV OUT jack on the unit to the corresponding input jacks on your TV using the supplied AV cable as shown below. Right side of the unit Plug into the “AV OUT” jack. TV Note: The signal does not come out from AV OUT jack when the unit is set to [TV] mode. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Revolving the LCD panel You can revolve the LCD panel of the unit clockwise a maximum of 180 degrees for use. You can also operate the unit after revolving the LCD panel 180 degrees and folding it back down. To revolve the LCD panel, place the unit on a stable and even surface such as on a table. Push the LCD panel up and then lift it into a vertical position. Revolve the LCD panel clockwise slowly 180 degrees. If you need, fold the LCD panel after revolving it. To revolve the LCD panel to its original position, open the LCD panel to a vertical position. Revolve the LCD panel counter clockwise slowly 180 degrees. • When finished using the unit, return the LCD panel to its original position. • Do not leave the LCD panel in the face-up position, or sudden shocks may damage it. Selecting the operation mode You need to select a operation mode before using this unit. Press MODE on the unit and the operation mode selection menu appears. Use b / B to select a mode then press ENTER. • Select [DISC] to playback the inserted disc. • Select [TV] to view the TV connecting the antenna. • Select [USB] to playback the file(s) in the connected 7 Adjust the settings BUTTON 1 Display setup menu: SETUP 2 Select a desired option on the first level: v V 3 Move to second level: B 4 Select a desired option on the second l...