Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
yyDo not extract the USB device during operation (play, etc.). yyA USB device which requires additional program installation when you have connected it to a computer, is not supported. yyUSB device: USB device that supports USB1.1 and USB2.0. yyMovie, music and photo files can be played. For details of operations on each file, refer to relevant pages. yyRegular back up is recommended to prevent data loss. yyIf you use a USB extension cable, USB HUB or USB Multi-reader, the USB device may not be recognized. yySome USB device may not work with this unit. yyDigital camera and mobile phone are not supported. yyUSB Port of the unit cannot be connected to PC. The unit cannot be used as a storage device. ,,Note 26 System Setting 3 System Setting Settings Initial Setup When you turn on the unit for the first time, the initial setup wizard appears on the screen. Set the display language and network settings on the initial setup wizard. 1. Press 1 (POWER). The initial setup wizard appears on the screen. 2. Use W/S/A/D to select a display language and press ENTER (b). 3. Read and prepare the preparations for the network settings and then press ENTER (b) while [Start] is highlighted. If wired network is connected, the network connection setting will automatically be finished. 4. All available networks are displayed on the screen. Use W/S to select [Wired Network] or desired SSID of wireless network and press ENTER (b). If you have security on your access point, you need to input the security code as necessary. 5. Use W/S/A/D to select the IP mode between [Dynamic] and [Static]. Normally, select [Dynamic] to allocate an IP address automatically. 6. Select [Next] and press ENTER (b) to apply network settings. Network connection status is displayed on the screen. For details on network settings, refer to “Connecting to your Home Network” on page 20. 7. Check all the settings that you have set in the previous steps. Press ENTER (b) while [Finish] is highlighted to finish the initial setup settings. If there is any settings to be changed, use A/D to select [Previous] and press ENTER (b). 27 System Setting 3 System Setting Adjust the Setup Settings You can change the settings of the player in the [Setup] menu. 1. Press HOME (n). 2. Use A/D to select the [Setup] and press ENTER (b). The [Setup] menu appears. 3. Use W/S to select the first setup option, and press D to move to the second level. 4. Use W/S to select a second setup option, and press ENTER (b) to move to the third level. 5. Use W/S to select a desired setting, and press ENTER (b) to confirm your selection. [DISPLAY] Menu TV Aspect Ratio Select a TV aspect ratio option according to your TV type. [4:3 Letter Box] Select when a standard 4:3 TV is connected. Displays theatrical images with masking bars above and below the picture. [4:3 Pan Scan] Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your TV screen. Both sides of the picture are cut off. [16:9 Original] Select when a 16:9 wide TV is connected. The 4:3 picture is displayed with an original 4:3 aspect ratio, with black bars appearing at the left and right sides. [16:9 Full] Select when a 16:9 wide TV is connected. The 4:3 picture is adjusted horizontally (in a linear proportion) to fill the entire screen. You cannot select [4:3 Letter Box] and [4:3 Pan Scan] option when the resolution is set to higher than 720p. ,,Note Resolution Sets the output resolution of the HDMI video signal. Refer to page 17 for details about the resolution setting. [Auto] If the HDMI OUT jack is connected to TVs providing display information (EDID), automatically selects the resolution best suited to the connected TV. [1080p] Outputs 1080 lines of progressive video. [1080i] Outputs 1080 lines of interlaced video. [720p] Outputs 720 lines of progressive video. [576p] Outputs 576 lines of progressive video. [576i] Outputs 576 lines of interlaced video. 1080p Display Mode When the resolution is set to 1080p, select [24 Hz] for smooth presentation of film material (1080p/24 Hz) with a HDMI-equipped display compatible with 1080p/24 Hz input. yyWhen you select [24 Hz], you may experience some picture disturbance when the video switches video and film material. In this case, select [50 Hz]. yyEven when [1080p Display Mode] is set to [24 Hz], if your TV is not compatible with 1080p/24 Hz, the actual frame frequency of the video output will be 50 Hz to match the video source format. ,,Note HDMI Color Setting Select the type of output from the HDMI OUT jack. For this setting, please refer to the manuals of your display device. [YCbCr] Select when connecting to a HDMI display device. [RGB] Select when connecting to a DVI display device. 3D Mode Select the type of output mode for Blu-ray 3D disc playback. [Off] Blu-ray 3D disc playback will output as 2D mode like a normal BD-ROM disc playback. [On] Blu-ray 3D disc playback will output as 3D mode. Wallpaper Changes the background of the initial screen. Home Menu Guide T...