Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Samsung Dateigröße: 2.15 mb Dateiname: Unterrichtssprache:

Dieses Gerät hat auch andere Anweisungen:

DVD-Player - SH-S182D (1011.01 kb)

Reading / Recording Speed Reading Speed(MAX) DVD-ROM(S)(16X), DVD-ROM(D)(8X), DVD-R (12X), DVD-RW (8X), DVD+R (12X), DVD+RW (8X), CD-ROM (48X), CD-R (40X), CD-RW (40X), DVD+R DUAL (8X), DVD-R DUAL (8X), DVD-RAM(12X) Recording Speed(MAX) DVD+R DUAL (8X), DVD+RW (8X), DVD-R (18X), DVD+R (18X), DVD-RW (6X), CD-R (48X), CD-RW (32X), DVD-R DUAL (8X), DVD-RAM(12X) Select Languages English 1. Turn the PC off. 2. Open the cover as shown in the picture. 3. If necessary, attach the support devices on both sides of the drive - The support devices are PC accessories. Purchase a pair if necessary. (SCREW : M3 X 6 X 4 ) 4. Insert the DVD Writer after removing the plate as below Be sure to use the screws (M3x6) provided with the product. - Using screws other than M3x6 may cause malfunction. Be sure that the screws are tightened securely in place. Loosely tightened screws may result in an increased level of noise. Select Languages English Connecting the Power Cable Hold the power cable (with four pins) in the power box within the computer with the cutoff edges( ) facing up and connect it to the power port in the back of the DVD Writer A -Cutoff edges 1 +5V DC 2 Ground 3 Ground 4 +12V DC Improperly connected power cable may cause malfunction. Check the direction of the power cable and the cutoff edges before connecting the cable. Connecting E-IDE Cable When you use one E-IDE cable Set the jumper to SL (slave) in the Master/Slave port in the back of the DVD Writer a : Slave Drive (Select the SL jumper) b : HDD c : MotherBoard When you use two E-IDE cables Set the jumper to MA (Master) in the Master/Slave port in the back of the DVD Writer. When you have one DVD Writer: Set it to MA (Master) a : Master Drive (Select the MA jumper) b : HDD c : Motherboard d : Primary 1 e : Secondary 1 When you have one DVD Writer and the other ODD products: Set it to MA (Master) / SL (Slave), a : Master Drive (Select the MA jumper) b : Slave Drive (Select the SL jumper) c : HDD d : Motherboard e : Primary 1 f : Secondary 1 Connecting the Jumper to the Master/Slave Port Connect the jumper to the slot in the back of the DVD Writer. When you connect the jumper to MA (Master), the drive runs as the master, and when you connect it to SL (Slave), the drive runs as the slave. When you connect it to CS (CSEL), you can control the device using the host interface signal CSEL. (Connection to MA is recommended.) MA : Master SL : Slave CS : Cable Select(CSEL) Connecting the Audio Cable (When Connected to the Sound Card) To listen to the sound from the drive in Analog mode, connect the audio output on the DVD Writer to the audio input of the sound card using an audio cable (4-pin). Connecting the Digital output terminal. For clearer sound, use a digital output terminal. Digital output terminal is only available with the Sound card which support Digital output. For using Digital output terminal, recommend to buy & use the sound card. Select Languages English 1. Go to 2. Click Firmware on the menu bar (in the upper right-hand corner). 3. Click Firmware Downloads. Check for your drive model and start downloading. Select Languages English Confirming Using [Device Manager] Windows 98 SE/Me 1. Click [Start] - [Settings] - [Control Panel] - [System] 2. Click on the [Device Manager] tab in the System Properties window. 3. Click CDROM drive in the Device Manager window. 1 in the picture in the left appear if the driver is installed properly. Windows 2000 1. Click [Start] - [Settings] - [Control Panel] - [System] 2. Click on the [Hardware] tab in the System Properties window and then click on the [Device Manager] tab. 3. Click DVD/CD-ROM drive in the Device Manager window. 1 in the picture in the left appear if the driver is installed properly. (Stamp) Windows XP 1. Go to [Start] - [Settings] - [Control Panel] [ Performance and Maintenance] 2. Click [Administrative Tools] icon in the Performance and Maintenance window. 3. Click [Computer Management] icon in the Administrative Tools window. 4. Click [Device Manager] icon in the Administrative Tools window and then click DVD/CD-ROM drive. 1 in the picture in the left appear if the driver is installed properly. Select Languages English When the On/Off light is orange, do not turn the PC off or remove the DVD Writer as it may cause damage in the drive. How to Use a Horizontally Installed Drive You can use 3.15 Inch or 4.72 Inch (8cm or 12cm) discs. The drive cannot read the disc properly if any part of the disc is place outside the tray guiding line. How to Use a Vertically Installed Drive This drive can be installed vertically. You can use only the 4.72 Inch (12cm) discs. (You cannot use the 3.15 Inch (8cm) discs) The drive cannot read the disc properly if any part of the disc is place outside the tray guiding line. Select Languages English The DVD Writer allows writing DVD RW discs using...

Herunterladen

Geben Sie zwei Ziffern: