Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
.Change the settings in “Digital Audio Output” (.page 47). [Note] You cannot use DTS Digital Surround decoders not suited to DVD. To enjoy stereo or Dolby Pro Logic Connect a digital amplifier or system component. .Change the settings in “Digital Audio Output” (.page 47). Speakers (Example) Connect three or more speakers for surround sound. Optical digital audio cable Do not bend sharply when connecting. Insert fully, with this side facing up. Amplifier LR Analog connection R - AUDIO - L To enjoy stereo or Dolby Pro Logic Connect an analog amplifier or system component. Amplifier or system component Audio cable This unit Recording to digital recording equipment or cassette tapes Digital recording You can record the digital signal directly to digital recording equipment (. Connection [A] above). [Note] .With DVD, the following conditions must be met: a the disc doesn’t have protection preventing digital recording, and b the recording equipment can handle signals with a sampling frequency of 48 kHz. .You cannot record DTS signals. .You cannot record MP3. When recording DVDs, make the following settings. V.S.S.: OFF (.page 37) PCM Down Conversion: On (.page 47) Dolby Digital: PCM (.page 47) DTS: Off (.page 47) Analog recording You can record to a cassette deck or other recording equipment (. Connection [B] above). There are no limitations on recording analog signals as there are with digital signals. 42 Connecting other video equipment Connecting other video equipment Connecting to the L2 input terminals on the front of the unit Connecting to the input terminals on the rear of the unit, L1 and L3 (L2) POWER/STANDBY S VIDEO IN VIDEO IN LINE 2 L (mono) AUDIO IN R / Audio/Video cable (included) S video cable§ yellow white red This unit Other video equipment Connect to the video and audio output terminals. § By using the S video cable instead of the yellow video cable you may make recordings of higher picture quality. [Note] If the audio output of the other equipment is monaural, connect to L/ MONO. (Both left and right channels are recorded when connected through L/MONO.) R-AUDIO-L OUT R-AUDIO-L R-AUDIO-L VIDEO VIDEO S-VIDEO S-VIDEO (L3) (L1) IN 1 IN 3 This unit Audio/Video cable (included) S video cable§ red white yellow Other video equipment Connect to the video and audio output terminals. § By using the S video cable instead of the yellow video cable you may make recordings of higher picture quality. [Note] If audio output on the other equipment is monaural, use a stereo- monaural conversion cable (not included). Advanced operation 43 Other antenna connections Other antenna connection to the unit Other antenna connection from the unit to the television Use one of the following connections to suit the antenna lead. . A single twin lead 300–75 . transformer (not included) from the antenna To this unit’s RF IN terminal (Flat) Twin lead 300 . cable . A twin lead and a coaxial cable from the antenna Advanced operation (Flat) Twin lead 300 . cable (Round) VHF/UHF band mixer (not included) 75 . coaxial cable To this unit’s RF IN terminal . Two twin leads from the antenna Use one of the following connections to suit the antenna terminals on your television. Refer to the television’s operating instructions. . A twin lead and coaxial plug terminal Television VHF VHF/UHF band separator (not included) UHF 75 . coaxial cable . A twin lead terminal 75–300 . transformer (not included) Television VHF or UHF 75 . coaxial cable . Two twin lead terminals Television VHF/UHF band separator VHF (not included) UHF 75 . coaxial cable . Multiple antenna terminals 300–75 . transformer (not included) (Flat) Twin lead 300 . cable VHF/UHF band mixer (not included) ANT 2 ANT 1 Split out Television 75 . coaxial cable To this unit’s .Connect to one of the terminals, then change the television’s RF IN terminal setting as necessary. .If your television has both lead and coaxial VHF terminals, use the lead connection to minimize signal loss. 44 Changing the remote control code 1 While stopped Press [SETUP] to show the menus. Hitachi DVD players and recorders use the same remote control system so they may respond unintentionally to a command from this remote control. Change the code on this unit and its remote control (the two must match) if you place equipment close together. .Use “1”, the factory set code, under normal circumstances. OPEN/CLOSE SETUP ERASE F Rec POSITION MEMORY MARKER AUDIO INPUT SELECT CM SKIP STATUS FRAME DISPLAY STOP PAUSE PLAY DVD VCR Plus+ TV/VIDEO REC MODE REC CH VOLUME TV TVDVD 1 2 3 7 8 9 0 100 4 5 6 SLOW/SEARCH SKIP DIRECT NAVIGATOR TOP MENU MENU RETURNFUNCTIONS PROG/CHECK TIME SLIPADD/DLT ENTER PLAY LIST CANCEL POWER .... SETUP 3, 4, 2, 1 ENTER Numbered buttons TAB SELECT Antenna System Auto Channel Setting Channel Caption Preset Channel Caption Manual Channel Caption VCR Plus.. CH Setting CATV Channel SETUP RETURN Set Up Disc Video Audio Display TV Screen 2 Press [3, 4] to select “Set Up” and press [1]. 3 Press [3, ...