Stimmen - 5, Durchschnittliche Bewertung: 4.4
(
)
)
|
Anleitung Zusammenfassung
When in use the internal backlighting will illuminate the controls. 3. After the unit has been turned on load a disc into the disc slot (lable side up). Adjust the viewing angle by pivoting the screen to optimize the picture quality. 4. Remember to turn the unit off and pivot the LCD to the locked position when not in use. Overhead Dome Lights The lights integrated into the ADV200 are controlled by a three position slide switch. Sliding the switch to the on position will turn the lights on. The off position will prevent the lights from turning on at all times, and the auto position will allow the lights to turn on and off with the vehicle’s interior lighting. Refer to the Installation Manual for the wire connections. NOTE: Do not leave the vehicle unattended with the dome light switch in the on position, as this could result in a discharged battery. Dom e Light Switch -15 128-7252A 15 of 35 Remote Sensor The ADV200 incorporates two Infrared sensors which relay signals from the remote control to allow the unit to be controlled simply by pointing its remote control at the remote sensor eye. The repeater function allows control of auxiliary equipment such as an Audiovox Video Cassette Player. The infrared sensor can relay signals from most manufacturer’s remote controls to its respective component connected to the AV 1 input. In this case you must use the remote control supplied with the component. Remote Sensor Eye Remote Sensor Eye Accessories Wireless Headphones The ADV200 includes a built-in infrared transmitter for use with ADVENT Wireless Headphones (Part Number IRHSN). The volume can then be adjusted using the controls on each headset. Any number of wireless headphones may be used but they must be used within a line of sight from the transmitter, as infrared transmissions, like visible light travel only in a straight line. See the documentation accompanying your Audiovox Wireless Headphones. -16 128-7252A 16 of 35 Wired Headphones There are two 1/8” headphone jacks on the ADV200 that can be used with any standard wired stereo headphones. These jacks are controlled by the volume up / down buttons on the ADV200 or the remote control. Wireless FM Modulator The ADV200 is equipped with buit-in wireless FM Modulator*, that allows you to listen to the ADV200 audio signal by tuning your vehicle’s radio to the selected frequency, (88.3, 88.7, 89.1, 89.5, 89.9MHz). This feature is accessed by using either the FM transmitter buttons on the remote (On/Off, Channel Select) or the FM Select button on the unit. AV1 Input The AV1 video input may be connected to a Video cassette Player (VCP), video game system, or other audio / video devices. To access the A/V1 input, turn the ADV200 on and press the source button on the ADV200 or the Source button on the remote control until “AV1” is displayed on the screen. Turn the video source component on with its power button or remote control. The ADV200 is now ready to play the audio and video signals from the source connected to AV1 input. The AV1 input requires a 8010730 cable. *NOTEIn certain areas where there are a large number of FM radio stations (e.g. large cities, urban areas), the reception of the FM signal from the overhead pod may not be satisfactory, resulting in static, distorted sound or signal bleed thru from strong local radio stations. This is not a defect in the product, but the result of a stronger local radio station overpowering the wireless FM transmitter in your overhead pod. If wireless reception is unsatisfactory, an optional wired relay box (Audiovox P/N SIRSWB) can be installed which will improve audio quality. Please contact the installer if this is the case with your product. -17 128-7252A 17 of 35 AUX A/V Input The ADV200 will accept an audio/video input through the RCA jacks located on the side of the unit. The audio / video device could be a video game system, video camera, or other input device. Audio/Video Out The ADV200 provides an AV output for an optional video monitor(s). (Refer to page 6 of the Installation Guide for more details.) This output will provide an A/V signal that duplicates the signal processed by the ADV200 to an additional monitor or video display. The audio signal can also be used to feed an AUX input on a vehicle radio if available. Please see your installer for more information. DVD Basics To get the optimum use out of the DVD player, make sure you read this section completely. Regional Coding Both the DVD player and disc are coded by region. These regional codes must match in order for the disc to play. If the codes don’t match, the disc won’t play. This unit’s code is region 1. Other regional codes cannot be played in this unit. The unit will display “WRONG REGION.” -18 128-7252A 18 of 35 Types of Discs your DVD will play • DVD discs – DVDs discs which contain video. • Audio discs – Audio CDs that contain music or sound content only. • MP3 discs – A disc that contains audio files (for example, a CD-R/CD-RW with downloaded...
Dieses Handbuch ist für folgende Modelle:DVD-Player - ADV200P (391.05 kb)
DVD-Player - ADV200S (391.05 kb)