Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
This DVD-RAM Drive adopts RPC-II, the Phase II System of RPC (Regional Playback Control) for “Standard Specification Model”, on the basis of a contract with the CSS (Contents Scramble System) organization. (all of our former DVD-RAM Drives adopted RPC-I, the Phase I System.) The CSS rule requires that all the products not only DVD-RAM Drives but also PC systems installing DVD-RAM Drives sold from Jan.1, 2000 need to support RPC-II described above. To playback a DVD-Movie Software with the Regional Code specified by using a DVD-RAM Drive with RPC-II adopted, either the hardware or software used as applications on PC system side is also required to meet RPC-II. Namely, in the status that a hardware or a software for a DVD-Movie Playback Application planned to use in a PC does not support RPC-II, if the "RPC-II (Standard Specification) Drive" is used in combination, DVD-Movie Softwares with the Regional Code specified (most of DVD-Movie Softwares currently available on the market) cannot be reproduced. So, in such a case, "RPC-I Specifications Supported Model" must be purchased for a while. However, all the drive manufacturers must obey to the deadline specified by the CSS rule saying; all DVD-RAM Drives have to implement Phase II from Jan.1, 2000. So we recommend that you will change your DVD-Movie Playback Hardware or Software to those applicable to the PRC-II as soon as possible and investigate to combine your system with the RPC-II Specification Drives. Since we determine the drives are of RPC-I or RPC-II when manufacturing at factory and ship, the specification change after shipping is not available in principle. Especially, changing the RPC-II specification drive to the RPCI is prohibited by the CSS rule. In the combination of the drive and PC system with RPC-II supported, as far as the Regional Code of a DVD-Movie Software and the code memorized in the RPC-II Specification Drive coincides, the Movie Software is allowed to carry out. In the RPC-II Specification Drive, the region change by an end user is permitted up to 5 times in total including the initial region set. After change to the fifth region is carried out, the Drive enters Parm State (“no change allowed” status). The drive with Parm State is permitted up to 4 times of "reinitialization" by a drive manufacturer or a specific service center authorized by the CSS. Since it is considered that the reinitialization is carried out after the completion of the region confirmation through test items in the PC manufacturer’s manufacturing line or the completion of drive repair, etc., the number of reinitialization times may vary from 0 (no reinitialization available) to 4 times. So, we recommend that not to disclose the reinitialization process to end users but only to inform the number of region setting times as "end user’s direct region setting is available up to 5 times in total." Page 2 Product Specification OD-A017-02 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 Precaution This equipment (an optical disc drive) handled under the conditions out of product specifications may cause injury, heat generation, trouble, erroneous operation and performance degradation, so, care will be necessary, and proper handling according to the precautions shown below will be required. In case of mishandling without keeping the cautions, safety, reliability and performance of the product are not guaranteed. For systems using this equipment, please note it above mentioned on manuals etc. to understand the users completely. Cautions (1) Don’t loosen screws except persons trained with specified instructions. The reliability, safety and performance specified in this specification can not be satisfied. (2) Don’t modify this equipment. The reliability, safety and performance specified in this specification can not be satisfied. (3) Don’t insert any objects or cartridge other than specified from the cartridge insertion slot. It may cause trouble or erroneous operation. (4) Don’t give excessive vibration and shock this equipment. It may cause trouble or erroneous operation. (5) Toshiba Corporation makes no warranty of any kind, either expressed or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. This product may sustain damages which may cause errors and failures. The causes are not confined to what are mentioned or implied in this document. Therefore, the possibilities of error and failure should be taken into consideration when furnishing systems should be protected by such means as system backup and mirroring disk subsystem, especially when this product is used for systems as medical appliances. Toshiba Corporation shall not be liable for incidental or consequential losses or damages to tangible property, injury or death of person in connection with the errors and failures which may occur when furnishing, operating or using this product (6) When a disc cannot be ejected because of some troubles, etc., t...