Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
• Remove the batteries from the remote if it will not be used for a long period of time. The batteries used in the remote control may present a fire or chemical burn if mistreated. Do not recharge, disassemble, incinerate, or heat the battery (~2120F). Keep batteries away from children. 1 Page 1 Page 14 Coby Electronics Corporation GETTING STARTED Overview of Audio/Video Connections S-VIDEO Composite Video 2-Channel Audio S-VIDEO Cable Coaxial Input Amplifier with Digital Decoding Connect the AC power cord to the wall outlet AFTER all other cables are connected. Connect only one type of audio or video connection at a time to minimize interference. Page 15 GETTING STARTED Standard Television Connection at a Glance Green Yellow To TV Composite Video Input To TV Component Video Input Blue Red Y Y Connect the player’s Composite Video Output to the TV’s Composite Video Input (yellow). Connect the player’s 2-Channel L&R Audio Outputs to the TV’s L&R Audio Inputs (red/white). Connect the player’s Component Video Output to the TV’s Component Video Input (red/green/blue). Connect the player’s 2-Channel L&R Audio Outputs to the TV’s L&R Audio Inputs (red/white). The player is equipped with composite AV outputs at the rear panel (yellow/red/white). Your TV will require at least one set of AV inputs. The supplied AV patch cord will connect your player’s AV output to your TV’s inputs. Depending on the brand of your TV, you may need to press a button labeled “Line”, “Input”, or “Video/TV” in order to set your TV to the correct input line. This will switch the TV from broadcast reception mode to on of the AV input signals. (Some TVs may have more than The player is equipped with 2-channel stereo or 5.1- on AV input line. channel surround sound outputs on the rear panel. For stereo or surround sound, a Stereo TV or Surround AV receiver is necessary. For Mono TVs, you can connect either the Left or Right stereo audio output to the Mono TV’s audio input. White Red White Red Progressive Scan Video (480p) Connection Page 16 Coby Electronics Corporation GETTING STARTED Use only ONE of the following connections to avoid signal interference: 1) 2.1-Channel Audio Out 2) Coaxial Digital Audio Out* *requires a Digital Decoding Amplifier Component or Composite Video Connection Component, Composite, or S-Video Connection Digital Output can be output in two formats: Raw or PCM. For more information, please see the “Setup > Audio Settings” section of this manual or refer to your amplifier’s documentation. Stereo (2-Channel) Audio Connection with Amplifier Digital Audio (Surround) Connection with Digital Decoding Amplifier GETTING STARTED GETTING STARTED Power Supply This unit should be used with 100-240V 50/60Hz AC wall outlets, only. Complete all system connections first before connecting the power. Do not connect the power plug to a power outlet other than that which is indicated here and on the label as this may result in the risk of fire or electric shock. Do not handle the power plug with wet hands. Doing so may cause electric shock. Power Management If the player will not be in use for a long period of time, set the Power Switch to the OFF position, unplug the player, and remove the batteries from the remote control. 1 Page 1 BASIC OPERATIONS BASIC OPERATIONS Basic Playback 1. Prepare the connections and power supply. Set the Power Switch to the ON position to turn the player on. 2. Select the video line. Set your TV to display the video line connection that corresponds to your DVD player (e.g., AV1, AV2, S-Video, Component, DVD, etc.) The DVD output will be displayed on the TV screen when the proper line has been selected. 3. Load a disc. Press the Open/Close button to open the disc tray. Insert a disc with the label-side up. Press the Open/Close button again to close the disc tray. • If a single-sided disc is inserted upside-down, the player will display “NO DISC” or “BAD DISC”. 4. Start playback. Press PLAY to start playback. • Some discs may start playing automatically or display a DVD menu specific to the disc. If a menu appears, use the NAVIGATION keys to select a desired feature or option and then press ENTER to confirm. Play/Pause/Stop • Press to play the disc for the first time. • Press during playback to pause. Press again to resume playback. • Press during playback to stop the disc (“Pre-Stop”). Press to resume playback at the time-point at which the disc was stopped. • Press when the disc is “Pre-Stopped” to stop playback completely. (When is pressed, the disc will start playing from the beginning.) Previous/Next (Skip) • Press to skip to the next track (DVD, CD, etc). • Press to return to the previous track (DVD, CD, etc). Forward/Reverse (Search) • Press and hold to fast forward through the current track. Continue holding to change the rate of forward playback. Normal x2 x4 x8 x16 x32 • Press and hold to reverse through the curren...