Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
B), the hinges are locked. They cannot snap shut. : Risk of injury! Whenever the hinges are not locked, they snap shut with great force. Ensure that the locking levers are always fully closed or, when detaching the oven door, fully open. Detaching the door 1. Open the oven door fully. 2. Fold up the two locking levers on the left and right (figure A). 3. Close the oven door as far as the limit stop. With both hands, grip the door on the left and right-hand sides. Close the door a little further and pull it out (figure B). Attaching the door Reattach the oven door in the reverse sequence to removal. 1. When attaching the oven door, ensure that both hinges are inserted straight into the opening (figure A). 2. The notch on the hinge must engage on both sides (figure B). 3. Fold back both locking levers (figure C). Close the oven door. : Risk of injury! If the oven door falls out accidentally or a hinge snaps shut, do not reach into the hinge. Call the aftersales service. Rails Hot soapy water: Soak and clean with a dish cloth or brush. Telescopic shelves Hot soapy water: Clean with a dish cloth or a brush. Do not remove the lubricant while the pullout rails are pulled out – it is best to clean them when they are inserted. Do not soak or clean in the dishwasher. Accessories Hot soapy water: Soak and clean with a dish cloth or brush. Area Cleaning agents .... .... .. .... .. .... .. .. .. .. .. .. .. .. .. Removing and installing the door panels To facilitate cleaning, you can remove the glass panels from the oven door. Removal 1. Detach the oven door and lay it on a cloth with the handle facing down. 2. Pull off the cover at the top of the oven door. Press in the tabs on the left and right using your fingers (fig. A). 3. Lift the top panel up and pull it out (fig. B). $ % 4. Lift the panel up and pull it out (fig. C). Clean the panels with glass cleaner and a soft cloth. .. : Risk of injury! Scratched glass in the appliance door may develop into a crack. Do not use a glass scraper, sharp or abrasive cleaning aids or detergents. Installation During installation, make sure that the lettering "top right" is upside down at the bottom left. 1. Insert the panel at an angle towards the back (fig. A). 2. Insert the top panel at an angle towards the back into the brackets. The smooth surface must face outwards. (fig. B). $ % 3. Put the cover back in place and press on it. 4. Attach the oven door. Do not use the oven again until the panels have been correctly installed. Troubleshooting Malfunctions often have simple explanations. Refer to the table before calling the after-sales service as you may be able to remedy the fault yourself. Malfunction table If a dish does not turn out as well as you had hoped, refer to the section Tested for you in our cooking studio, where you will find plenty of cooking tips and notes. Problem Possible cause Remedy/information The oven does The circuit Look in the fuse box and not work. breaker is check that the circuit defective. breaker is in working order. Power cut Check whether the kitchen light or other kitchen appliances are working. 0 and zeros Power cut Reset the clock. flash in the display. The oven does There is dust on Turn the control knobs back not heat up. the contacts. and forth several times. Error messages If an error message with “ appears, press the 0 button. The message disappears. A time function that has been set is cleared. If the error message does not disappear, please contact the after-sales service. You can take remedial action yourself if the following error message is displayed. Error message Possible cause Remedy/information “‹‚‚ A button was Press all buttons individudepressed for ally. Check whether any but- too long or is tons are jammed, covered covered up. up or soiled. : Risk of electric shock! Incorrect repairs are dangerous. Repairs may only be carried out by one of our trained after-sales engineers. Replacing the bulb in the oven ceiling light If the bulb in the oven light fails, it must be replaced. Heat- resistant, 40 watt spare bulbs can be obtained from our after- sales service or a specialist retailer. Only use these bulbs. : Risk of electric shock! Switch off the circuit breaker in the fuse box. 1. Place a tea towel in the oven when it is cold to prevent damage. 2. Unscrew the glass cover by turning it anti-clockwise. 3. Replace the bulb with one of the same type. 4. Screw the glass cover back in. 5. Remove the tea towel and switch on the circuit breaker. Glass cover You must replace a damaged glass cover. Suitable glass covers may be obtained from the after-sales service. Please specify the E number and FD number of your appliance. After-sales service Our after-sales service is there for you if your appliance needs to be repaired. We will always find the right solution in order to avoid unnecessary visits from a service technician. E number and FD number When calling us, please give the product number (E no.) and the production number (FD no.) ...
Dieses Handbuch ist für folgende Modelle:Backöfen - HB23AT520/07 (917.82 kb)
Backöfen - HB23AT520/35 (917.82 kb)
Backöfen - HB23AT520/45 (917.82 kb)
Backöfen - HB23AT520/56 (917.82 kb)