|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Confirm with ™. 10 The second rinsing process appears. Start with I. The appliance is rinsed. The rinsing time counts down on the display. A signal sounds after one minute. The descaling programme has finished. Empty the evaporator dish with the cleaning sponge. Empty the water tank and leave it to dry with the lid open. Dry the cooking compartment with a soft cloth and dry fully with the drying programme. Then delete the descaling hint in the display. Deleting the descaling hint 1 Set function selector to S. Use the rotary selector to select "Delete descaling hint". Confirm with ™. 2 A notification appears. Confirm with ™. Notes .The descaling programme must always be run through completely and cannot be cancelled. .Before cooking, remove any descaler residue from the cooking compartment. .If the descaling programme was cancelled due to a power cut, it must be restarted before using the oven again in order to remove any descaler residues from the appliance. Removing slide-in rails You can remove the slide-in rails for cleaning. Detaching the rails 1 Place a dishcloth in the cooking compartment to protect the stainless steel against scratches. 2 Undo the knurled nuts (Figure A). 3 Pull away the slide-in rails slightly sideward from the screw and pull it out toward you (Figure B). ........ Clean the rails in the dishwasher. Attaching the rails 1 Position the slide-in rails correctly with the stopper at the back. 2 Push the slide-in rails onto the bolt at the rear and then hook them in at the front. 3 Tighten the knurled nuts. Note: If you should lose a knurled nut, you can order it as a spare part from our after-sales service. Using knurled nuts other than the original ones will cause corrosion in the oven interior. Trouble shooting Malfunctions of ten have simple explanations. Please read the following notes before calling the af ter-sales ser vice. m Risk of electric shock! Incorrect repair s are dangerous. Repair s may only be carried out and damaged power cables replaced by one of our trained af ter-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch of f the circuit breaker in the fuse box. Contact the af ter-sales ser vice. Disruption Possible cause Solution Appliance not working, no display Plug not inserted Connect the appliance to the electricity mains Power failure Check whether other kitchen appliances are working Fuse defective Check in the fuse box whether the fuse for the appliance is in working order Operating error Switch off the fuse for the appliance in the fuse box and switch it on again after about 60 seconds Appliance cannot be started Appliance door is not quite closed Close appliance door Appliance does not work, display does not respond. 0 appears in the display Child lock activated Deactivate the child lock (refer to Child lock section) Appliance switches off on its own Safety shut-off: the appliance has not been operated for longer than 12 hours Confirm the message with ™, switch off the appliance and set it again. Appliance does not heat up, ° appears in the display Appliance is in demo mode Deactivate the demo mode in the basic settings The appliance cannot be started, the display shows an error message The water tank is empty Fill the water tank A lot of steam escapes at the top of the door Appliance is calibrating the boiling point or is preheating or the heating mode has been changed This is normal The appliance has not yet been calibrated Calibrate the appliance A lot of steam escapes at the side of the door Door seal soiled or loose Clean the door seal and insert it in the groove There is a "pop" noise during cooking Cold/warm effect with frozen food, caused by the steam This is normal The appliance is not producing steam properly Limescale has formed in the appliance Start the descaling programme Error message "Exxx" If an error message is displayed, turn the function selector to 0; if the display goes out, there was a non-recurring problem. If the error occurs repeatedly or the display remains on, please contact the after-sales service and inform them of the error code. Power cut Your appliance can bridge a power cut of a few seconds. Operation continues. If the power cut was for a longer period and the appliance was in operation, a message appears in the display. Operation is interrupted. Set the function selector to 0, then the appliance can be operated again as usual. Demo mode If the ° symbol appears in the display, the demo mode is activated. The appliance does not heat up. Briefly disconnect the appliance from the mains (switch off the household fuse or the circuit breaker in the fuse box). Following this, deactivate the demo mode in the Basic settings within 3 minutes (refer to the Basic settings section. Replacing the oven light For technical reasons the lamp cover cannot be removed. Lamp must only be replaced by Gaggenau after-sales service. Caution! Do not remove the lamp cover. This will damage the sealing. If the lamp ...
Dieses Handbuch ist für folgende Modelle:Backöfen - BSP221130/04 (484.83 kb)