Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
2.Unscrew the cover at the top of the oven door. To do this, unscrew the left and right screws (fig. A). 3. Lift the top panel up and pull it out and remove the two small seals (fig. B). 4.Unscrew the retaining clips on the right and left. Lift the panel and remove the clips from the panel (fig. C). 5.Remove the seal from the bottom of the panel (fig. D). Pull the seal and remove it up and out. Pull out the panel. 6. Pull the lower panel at an angle, upwards and out. 3. Stick the retaining clips onto the right and left-hand side of the panel, aligning them so that the retaining carriers are over 7. Do NOT unscrew the left and right- hand screws from the the screw holes, and then screw into place (fig. C). sheet metal part (fig. E). 4. Hook the seal in to the bottom of the panel again ( fig. D) . Clean the panels with glass cleaner and a soft cloth. : Risk of injury! Scratched glass in the appliance door may develop into a crack. Do not use a glass scraper, or sharp or abrasive cleaning aids or detergents. Installation During installation, make sure that the lettering "top right" is upside down at the bottom left of both panels. 1. Insert the lower panel at an angle towards the back (fig. A) . 2. Slide in the middle panel (fig. B) . 5. Insert the uppermost panel at an angle to the back into the brackets. Take care not to push the seal to the back ( fig. E) . 6. Insert the two small seals on the left and right of the panel again (fig. F). 7. Put the cover back in place and screw it on. 8. Attach the oven door. Do not use the oven again until the panels have been correctly installed. Troubleshooting Quite often, when there is a malfunction, it is usually a small irregularity which is easy to rectify. Before contacting the Technical Assistance Service, try to determine the cause of the fault using the following table. Troubleshooting table Fault Possible cause Solution/ advice The oven does not The fuse has Check the condition work. blown. of the fuse/circuit breaker in the fuse box. Power cut Check that the light in the kitchen and other household appliances are working. The 0 symbol lights Power cut Set the time once in the display with again. some zeros. The oven does not There is dust in Turn the control knob work. the contacts. several times in both directions. Fault Possible cause Solution/ advice The oven door does The oven door Wait until the oven not open. The Hsymbol lights up on the display panel. has been locked by the self- cleaning function V. has cooled and the H symbol turns off. The display shows ”‰ . The appliance has been auto- Turn the function control knob to the matically turned off. zero setting. Error messages When the indicator displays an error message with “ , press the 0 sensor. The message will disappear. The set time function will be deleted. If the error message does not disappear, call the Technical Assistance Service. The following error messages can be solved by the user. Error Possible cause Solution/ advice message “‹ ‚‚ A sensor has been pressed for too long or has got stuck. Press all the sensors one by one. Check if a sensor is stuck, covered or dirty Error Possible cause Solution/ advice message “‚ ‹‡ The door lock has been activated with the door open. Press the 0 sensor. You can now begin programming again. “‚ ‚† The temperature inside the oven is too high. The door oven is locked and heating has stopped. Wait until the oven has cooled. Press the 0 sensor and reset the time. : Risk of electrical discharge and the resulting shock. ! Incorrect repairs can be dangerous. Repairs can only be carried out by qualified personnel from the Technical Assistance Service. Changing the oven bulb If the oven light bulb is damaged it must be replaced. Special 25 W, E14, 220 V- 240 V heat-resistant light bulbs (to 300 . C temperature) can be obtained from the Technical Support Service or in specialist shops. Only use this type of bulb. : Risk of electrical discharge and the resulting shock. ! Disconnect the appliance from the mains. Ensure that this is turned off. 1. Place a dishcloth into the cold oven to avoid damage. 2. Remove the glass protection by unscrewing it to the left. 3. Replace the bulb with a similar bulb. 4. Screw the protection glass back into place. 5. Remove the dishcloth and switch the oven back on at the mains. Protective glass panels Damaged protective glass panels must be replaced. Protective glass panels cay be obtained from the Technical Assistance Service. Please quote your appliance's product number and production number. After- sales service Our after-sales service is there for you if your appliance needs to be repaired. We will always find the right solution in order to avoid unnecessary visits from a service technician. E number and FD number When calling us, please give the product number ( E no. ) and the production number ( FD no. ) so that we can provide you with the correct advice. The rating plate containing these numbers can be found on...