Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
This lining absorbs splashes produced during baking and roasting, dissolving them while the oven is working. This cleaning will be most effective at higher temperatures and during longer cooking times. Proceed as follows if the oven is still dirty after being used several times: 1. Thoroughly clean the bottom and any walls that do not have this lining. 2. Programming the hot air function N. 3. Empty the oven and then leave it on with the door closed for approximately 2 hours at maximum temperature. The ceramic lining will regenerate. Once the oven has cooled down, remove any brown and white stains with water and a soft sponge. Slight discolouration of the lining does not affect its self- cleaning performance. Caution! ¦ Do not use abrasive cleaning products. These would scratch and impair the highly porous lining. ¦ Never use oven cleaning products on ceramics. If oven cleaner is spilled on this accidentally, immediately remove it using lots of water and a sponge. Cleaning the oven's enamelled bottom and walls Use a cleaning cloth and hot water with a little soap or vinegar. If very dirty, use a fine steel scourer or a special oven cleaning product. These must only be used when the oven interior is cold. Do not use metal scourers or special oven cleaning products on self-cleaning surfaces. Light The oven light can be turned on manually to facilitate cleaning. Turning on the oven light Turn the function control knob to the ^ position. The light will come on. The temperature control knob must be turned off. Turning the oven light off Turn the function control knob to the Uposition. Removing the grill heating element The grill heating element can be removed in some ovens to facilitate cleaning. : Risk of burns. ! The oven must be cold. 1. Pull the grill element handle towards you and push it upwards until you hear it click into position ( figure A) . 2. At the same time, hold the grill element and swing it down (figure B). After cleaning, push the grill heating element up again. Push the locking handle down and secure the grill element. Removing the oven carriage The oven carriage can be easily removed to make cleaning the oven easier. Pull out the oven carriage its full limit. Hold the carriage on both sides, lift it slightly and remove it. Place it carefully on a flat surface. The base of the oven contains delicate components. After cleaning, the oven door can be refitted by repeating the procedure in reverse. Fitting and removing the glass panels To make cleaning easier, the glass from the oven carriage can be removed. Dismantling 1. Removing the oven carriage. 2. Remove the top cover of the oven carriage. To do this, unscrew the right and left- hand side screws ( figure A) . 3. Hold the glass in your hands ( left and right) and remove upwards (figure B). Place these on a cloth with the handle facing downwards. The inside glass with the hooks should not be removed from the oven carriage. In doors with three glass panels, the following step will also be necessary: 4. Unscrew the clips from the right and left and remove them (figure C). Remove the top glass panel. Clean the glass panels using a glass cleaning product and a soft cloth. : Risk of injury! Scratched glass in the appliance door may develop into a crack. Do not use a glass scraper, or sharp or abrasive cleaning aids or detergents. Installing Follow steps 3 to 5 for doors with two glass panels. 1. Insert the glass panel by tilting it backwards ( figure A) . When fitting the glass, ensure that the marking "right above" at the bottom left- hand side is upside down. 2. Position and screw the clips to the right and left ( figure B) . 3. Insert the glass panel into the carriage support. 4. Fit and tighten the screws on the cover. If the cover cannot be screwed into place, check that the glass panel has been correctly fitted on the support. 5. Close the oven carriage. Once the glass panels have been correctly fitted, the oven is ready to use. Troubleshooting Quite often, when there is a malfunction, it is usually a small irregularity which is easy to rectify. Before contacting the Technical Assistance Service, try to determine the cause of the fault using the following table. Troubleshooting table Fault Possible cause Solution/ advice The oven does not The fuse has Check the state of the work. blown. fuse in the fuse box. Power cut. Check that the light in the kitchen and other household appliances are working. The display panel Power cut. Set the time once shows a flashing 0 again. symbol and four zeros. The oven does not There is dust on Turn the control knobs heat up. the contacts. several times in both directions. Error messages When the display panel shows an error message with “ , press the 0 button. The message will disappear. The set time function will be deleted. If the error message does not disappear, call the Technical Assistance Service. The following error messages can be solved by the user. Error message Possible cause Solution/ advice ...