Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
The reminder message goes out once the water tank is empty. Filling the water tank Fill the water tank before each use with steam assistance. 1. Press lightly on the centre of the lower edge of the water tank (picture A) . 2. Pull out the water tank ( picture B) . " 3. Fill the water tank with cold water up to the " max" mark (picture C) . 4. Slide in the water tank all the way. Refilling the water tank If the water tank is empty, a signal sounds. " Fill water tank and slide in fully" appears in the display. Steam- assisted operation is interrupted. 1. Pull out the water tank. 2. Fill the water tank up to the " max" mark and slide it in fully. The steam- assisted operation continues. Emptying the water tank Empty the water tank after each steam- assisted use of the appliance. 1. Turn the operating mode selector back to the U off position and push it in. " Pumping-out" appears in the text display and .z © ( pumping out) appears in the temperature display. The remaining water in the evaporator system is pumped back into the water tank. After the pumping, "Pumping-out finished" appears. 2. Pull out the water tank slowly and level. 3. Remove the cover (Picture A) . 4. Empty the water tank ( Picture B) . . . 5. Thoroughly dry the water tank recess and the water tank. 6. Slide in the water tank. Switching off the appliance : Risk of scalding! When you open the appliance door, hot steam can escape. Open the appliance door carefully after cooking. Note: The appliance has a cooling fan. After the appliance is switched off, the cooling fan may continue to run. 1. Turn the operating mode selector back to the U off position 2. Press the operating mode selector in so that it stays in. The appliance switches off. Note: If the appliance is switched off after a steam- assisted operation, you will hear a pumping sound. The appliance is pumping the remaining water out of the evaporator system back into the water tank. " Pumping-out" appears in the text display. Only empty the water tank once " Pumping-out finished" is displayed. You can see in the temperature display whether there is high or low residual heat in the cooking compartment. Temperature Text display Meaning display • Residual heat Residual heat high high (above 120 °C) oe Residual heat Residual heat low low (between 60 ° C and 120 °C) Turning off the operation Press and hold the „ Stop button. The appliance turns off the current operation. The appliance is not switched off. You can now start a different operating mode. Interrupting and continuing an operation ( Pause) Briefly press the „ Stop button. The appliance interrupts the current operation. Press the . Start button to continue the paused operation. After each steam- assisted use 1. Switch off the appliance. The remaining water is pumped out of the evaporator system and back into the water tank. " Pumping-out" appears in the text display. 2. Only empty the water tank once " Pumping-out finished" has been displayed. 3. Empty and wash the water tank, and leave it to dry with the lid open. 4. Wipe the cooled cooking compartment down with a soft cloth. 5. Remove any dirt from the cooking compartment. Note: Remove limescale marks with a cloth soaked in vinegar, then wipe with clean water and rub dry with a soft cloth. Automatic safety cut-out The automatic safety cut- out is only activated if you have not made any settings on your appliance for a prolonged period. You can adjust the period of time after which your appliance shuts off. "Safety cut- out" appears in the text display and ‹‹ ‹ flashes in the temperature display. Appliance operation is interrupted. Turn the operating mode selector to the U position to deactivate it. Changing the basic settings Your appliance has various basic settings, which are preset at the factory. You can change these basic settings as required. 1. Switch on the appliance. 2. Press and hold the ± info button for 3 seconds to go to the basic settings menu. The text display shows " Select language: English" . If the appliance controls are locked, you must unlock them first. 3. Press the ± info button repeatedly until the current basic setting for the relevant submenu is displayed on the text display ( e. g. " Audible signal off") . 4. Using the temperature selector, set the required basic setting within a submenu (e. g. " Audible signal 2 minutes" ) . 5. Press and hold the ± info button for 3 seconds. Your basic setting is saved. Note: If nothing is entered after 15 seconds, the Basic settings menu is automatically closed. "Appliance is ready for use" appears in the text display. You can change the following basic settings: Basic settings menu Submenu Basic setting Setting symbol Language Select language Childproof lock Appliance unlocked ™‚ ‹ Appliance locked ™‚ ‚ Appliance perma- ™.‚ nently locked Audible signal Audible signal off ™„ ‹ Audible signal ™„ ‚ 30 seconds Audible signal ™„ . 2 minutes Audible signal ™„ „ 10 minutes Adjust individually* AUUUOUUU@ ™… .. . Basic settings ...