Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Do not use distilled water, highly chlorinated tap water (> 40 mg/l) or other liquids. Only use cold, fresh tap water, softened water or uncarbonated mineral water. The water hardness “hard“ ( ™… „ ) is the default setting. Change the setting if the water is softer. You can determine the water hardness with the test strips supplied or ask your water supplier. Notes ¦ If your water is very hard, we recommend that you use softened water. ¦ If you use only softened water, you can, in this case, set your appliance to the softened water hardness range. ¦ If you use mineral water, then set the water hardness range to hard. ¦ If you use mineral water, then it must be non-carbonated (see chapter: Filling and emptying the water tank) . 1. Use the temperature selector to set the water hardness range. Water hardness range Setting symbol (temperature display) softened ™… ‹ soft ™… ‚ medium ™… . hard ™… „ 2. Press and hold the ± info button for 3 seconds. Your setting is saved. ™† ‚ appears in the temperature display. Calibrating the altitude The altitude difference range “ 0 - 300 m“ ( ™† ‚ ) is the default setting. Change this setting if the location of the appliance is higher or lower than this. 1. Use the temperature selector to set the altitude difference range. Altitude difference Setting symbol (temperature dis- range play) Under 0 m ™† ‹ 0 - 300 m ™† ‚ 300 - 600 m ™† . 600 - 900 m ™† „ 900 - 1200 m ™† … 1200 - 1500 m ™† † 1500 - 1800 m ™† ‡ 1800 - 2100 m ™† . 2100 - 2400 m ™† ‰ above 2400 m ™† S 2. Press and hold the ± info button for 3 seconds. Your setting is saved. Setting the clock Note: When you press the KJclock function button, you have 3 seconds to set the clock using the rotary selector. Should this have been insufficient for you, you can amend the clock time later. ‹ : ‹‹ flashes in the clock display. 1. Briefly press the KJ clock function button to go to the setting mode. The KJand 3 symbols light up. ‚.: ‹‹ appears in the clock display. 2. Set the current time using the rotary selector. Your setting is accepted after 3 seconds. Changing the clock To subsequently change the time, press the KJclock function button repeatedly until the KJand 3 symbols light up again. Change the time with the rotary selector. Cleaning the appliance Clean your appliance before using it for the first time. 1. Remove the accessories from the cooking compartment. 2. Completely remove any residual packaging (e. g. chips of polystyrene) from the cooking compartment. 3. Clean the accessories and cooking compartment with hot soapy water ( see section: Cleaning and care) . 4. Fill the water tank with 400 ml water ( see section: Filling and emptying the water tank) . 5. Slide in the water tank all the way. 6. Switch on the appliance. To do this, press the operating mode selector so that it pops out. The appliance is then ready for use. 7. Using the operating mode selector, set % Top/bottom heat (see section: Operating the appliance) . 8. Use the temperature selector to set the temperature to 240 ° C. 9. Press the Y VarioSteam button repeatedly until the • z Y symbols light up ( see section: VarioSteam - steam- assisted cooking) . 10. Press the . Start button. 11. Switch off the appliance if the water tank is empty. To do this, turn the operating mode selector to the U off position and push it in. The remaining water will be pumped out of the evaporator system. The I symbol lights up. 12. Emptying the water tank ( see section: Filling and emptying the water tank) 13. Afterwards, wipe the cooled cooking compartment with hot, soapy water. Note: Remove limescale marks with a cloth soaked in vinegar, then wipe over with clean water and rub dry with a soft cloth. 14. Clean the outside of the appliance with a soft, damp cloth and soapy water. Operating the appliance In this section, you can read about ¦ how to switch your appliance on and off ¦ how to select an operating mode and temperature ¦ how to fill and empty the water tank ¦ when your appliance switches off automatically Switching on the appliance Press the operating mode selector to make it pop out. This switches on the appliance, and it is now ready for use. The ~ symbol lights up. Selects the operating mode and temperature a= Risk of scalding! by hot water. The water in the water tank may become hot. Empty the water tank before starting operating modes that do not use steam. Notes ¦ The operating modes / Low-temperature cooking and > EasyClean® can only be started if the cooking compartment has cooled down. There must be no residual heat ( • or oe) showing in the temperature display. ¦ For steam- assisted applications, you must fill the water tank (see section: Filling and emptying the water tank). 1. Switch on the appliance. 2. Turn the operating mode selector until the desired operating mode is selected. 3. Turn the temperature selector to change the default temperature. Note: If no default temperature is displayed, the temperature of your selected operating mode is set perma...
Dieses Handbuch ist für folgende Modelle:Backöfen - B45C42N0/35 (2.05 mb)