Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
At the end of the wash cycle Six beeps will indicate that the wash cycle has finished and the cycle indicator light (J) for the cycle will begin to die out. Turn off the appliance using the ON-OFF button. Turn off the water supply to the appliance and open the door. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better. Setting the Wash Cycle with a Delayed Setting the Wash Cycle with a DelayedSetting the Wash Cycle with a DelayedSetting the Wash Cycle with a DelayedSetting the Wash Cycle with a DelayedSetting the Wash Cycle with a Delayed Start Time Start TimeStart TimeStart TimeStart TimeStart Time By pressing the "F" button (see close-up view-'Control panel") the start of wash cycle can be delayed for between 1 to 12 hours. Each time the button is pressed, the display (G) will show the number of hours for the delay period. Choose the amount of time desired. After selecting the wash cycle, a short acoustic sig nal will sound and after a few seconds, the delay time on the dis play will blink, This indicates that the countdown has begun. After the time has lapsed, the cycle will start. NOTE: During the delay period, it is preferable not to change any of the settings, If this is necessary, all of the settings must be cancelled by pressing the ON/OFF button (D). At this point, all of the steps for "setting the wash cycle with a Delayed Start Time" and "Setting and Starting a wash cycle" must be repeated, following the instructions contained in the corresponding sections. If the door is opened to the unit during the delay period, the countdown will stop. It will begin again when the door is closed. All of the wash cycle set to reverse time function, we may in focus start circulate time. Wash Cycle adjustment Buttons Wash Cycle adjustment ButtonsWash Cycle adjustment ButtonsWash Cycle adjustment ButtonsWash Cycle adjustment ButtonsWash Cycle adjustment Buttons 1/2 load Button This button (see "close-up View - Control Panel", letter"E EEEEE") makes it possible to wash dishes using only the upper rack if there are not enough dishes for a full load. This will allow you to save on water and power. It can be used before setting any of the wash cycle, except for the intensive cycle ( if included in the wash cycle table). Please keep in mind that the amount of detergent should also be cut in half. .5. GBGBGBGBGB GBGBGBGBGB .6. Energy Saving Tips Wash Cycle Table -It is important to try and run the dishwasher when it is fully loaded in order to save on energy. To prevent odors from forming and food from caking onto the dishes, you can run the soak cycle. - Use the right amount of detergent: if you use too much detergent, the result will not be cleaner dishes, but, rather, a greater negative impact on the environment. - Choose the right wash cycle: the choice of cycle depends on the type of dishware, cookware and utensils being washed and how dirty they are. How to Keep Your Dishwasher in Shape After Every Wash Moving the Appliance After every wash, turn off the water supply to the appliance and If the appliance must be moved, try to keep it in the vertical position. leave the door slightly ajar so that moisture and odors are not If absolutely necessary, it can be positioned on its back. trapped inside. Seals Remove the Plug One of the factors that cause odors to form in the dishwasher is Before cleaning or performing maintenance, always remove the food that remains trapped in the seals. Periodic cleaning with a plug from the socket. sponge will prevent this from occurring. No Solvents or Abrasive Cleaning Products When You Go on Holiday To clean the exterior and rubber parts of the dishwasher, do not When you go on holiday, it is recommended that you run a wash use solvents or abrasive cleaning products. Use only a cloth and cycle with the dishwasher empty and then remove the plug from warm soapy water. the socket. Turn off the water supply and leave the door of the To remove spots or stains from the surface of the interior, use a appliance slightly ajar. This will help the seals last longer and pre- cloth damp and a little white vinegar, or a cleaning product made vent odors from forming within the appliance. specifically for dishwashers. Cycle Cycle Selection Information Description of Cycle Detergent Rinse Aid Heavy Duty Very dirty dishes, pots and pans. (not to be used with delicate items) Pre-wash with warm water. Extended wash at 70 . Rinse with cold water. Rinse with hot water. Drying. . 30g Normal Wash Normal dirty dishes, pots and pans. standard daily cycle. Pre-wash with cold water. Extended wash at 55 . Rinse with cold water. Rinse with hot water. Drying. . 30g Rapid Wash Economic, fast cycle to be used on not very dirty dishes right after they are used. No drying cycle. Short wash at 40 . Cold rinse . . 15g Glass ware (EN50242) Economic,test cycle for IECEN50242 Pre-wash with cold wate...