Stimmen - 3, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Depending on the pressure exerted on the button, the adjustment of running speed can be varied infinitely. Turn off by releasing the button. After releasing the button, the chuck is stopped and therefore, after-running of the equipment is prevented. To change the direction of rotation The selector button (1.4) determines the direction of rotation. -Turn button from right to left = clockwise rotation. -Turn button from left to right = anticlockwise rotation. -Selector button in central position = circuit interlock. Shifting speeds Change only when completely stopped! Using the shift lever (1.5), the speed can be changed. If the shift lever cannot be switched completely, slightly turn the chuck. • 1. Speed: lever forward - Figure 1 is visible. • 2. Speed: lever backwards - Figure 2 is visible. Torque adjustment By turning the adjustment ring (1.7), so that the corresponding symbol aligns with the arrow (1.6) the required torque can be adjusted. a) Drilling: Drilling symbol on adjustment ring aligns with the arrow = maximum torque. b) Screws: Torque corresponding to setting: • Position 1 = low torque • Position 18 = high torque Tool holding fixture, attachments Make sure that the machine is switched of and the battery block has been removed before changing the tool holding fixture, attachments and tools. Chuck BF-FX The chuck is used to clamp drills and bits. Fitting: -Place the chuck on the drill spindle (2.11) and twist until the hexagon key (2.10) of the chuck latches into the hexagon socket of the drill spindle. -Pull the unlocking ring (2.9) forwards, press the chuck onto the drill spindle up to the stop and release the unlocking ring. Removal: -Pull the unlocking ring forwards and remove the chuck. Changing tools -Turn the clamping sleeve (2.8) anti-clockwise to open the clamping jaws (2.7) (Note: the spindle is automatically locked when the machine is switched off). -Insert the tool into the chuck. -Clamp the tool by turning the clamping sleeve clockwise. Always make sure that the tool is clamped centrally in the chuck. Angle attachment DD-AS The angle attachment permits work (drilling, screwing) vertical to the machine’s longitudinal axis. Fitting: -place the angle attachment on the drill spindle and turn until it catches in the desired position (Note: The angle attachment can be fitted in 16 different angle settings). -Lock the angle attachment by turning the fastening ring (2.6) tightly clockwise. Removal: -Turn the fastening ring anti-clockwise up to the stop and remove the angel attachment. Fitting / removal of chuck on angle attachment The chuck is fitted on the shaft (2.5) of the angle attachment in the same way as on the drill spindle of the machine. Eccentric attachment DD-ES The eccentric attachment is used to hold bits. It allows screwing close to edges. Fitting / removing the eccentric attachment The eccentric attachment is fitted / removed in the same was as the angle attachment DDAS. 6 Changing tools -Pull the unlocking ring (2.4) back and remove the tool and/or insert the new tool. Toolholder CENTROTEC WH-CE The CENTROTEC toolholder enables rapid changes of tools with CENTROTEC shafts. Do not fit CENTROTEC tools at the round shaft section in a conventional chuck to prevent damage to the shaft. Danger of injury! When changing tools, handle the tool and its sharp cutters with special care and wear protective gloves, if necessary. Fitting -Pull the unlocking ring (2.14) forwards, press the chuck onto the drill spindle up to the stop and release the unlocking ring. Removal -Pull the release ring forwards and take off the toolholder. Changing tools -To insert or remove a tool with CENTROTEC shaft, pull the green release ring (2.13) back. On inserting the tool, turn it until its hex shank arbour (2.12) locks in place in the hexagonal shank of the drill spindle, and push the tool into the toolholder as far as it will go. Tool holding fixture in the drill spindle Bits can be fitted directly in the hexagon socket holder of the drill spindle (2.11) to make the machine lighter and shorter. Charge battery pack MC 15 The charger MC 15 can be used to charge all NiCd-Festool battery packs between 4.8 V and 12 V in the battery chamber (3.1). The charge process is controlled by a microprocessor. The optimum charging current is always used depending on the temperature, voltage and internal resistance. The LED (3.2) indicates the respective charging operation of the charger. LED yellow - steady = Charger is ready for use. LED green - flashing = Battery pack being charged. LED green - fast flashing = Battery pack being charged at max. charging current. LED green - steady = Battery pack fully charged, conservation charge on. LED red - flashing = General malfunction, e. g. incorrect polarity of battery pack, full contact not being made, short-circuit, battery pack faulty. LED red - steady = Temperature of battery pack is outside permissible limit. If the battery pack is removed from the charging chamber during...