Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Central Pneumatic Air Compressor Dateigröße: 3.27 mb Dateiname: 33567.pdf Unterrichtssprache:

Step 5: Place the socket on the nut. To begin tightening the nut, press the TRIGGER. Step 6: If the Air Ratchet stalls while tightening, do not continue attempts to tighten the nut with the Air Ratchet. DO NOT raise the outlet pressure of the air compressor. Use the appropriate tools and methods to tighten the nut. Step 7: When the nut has been tightened, remove the Air Ratchet and socket. Step 8: If available, check the recommended torque specification for the nut. You should use a torque wrench to torque the nut after using the Air Ratchet. For technical questions, please call 1-800-444-3353. Page #10 -- SKU: 33567 REV 12/02 MAINTENANCE Your Air Ratchet is best operated with an Airline Oiler. If you are using the Air Tool without an Airline Oiler, follow the steps below. Step 1: Disconnect the Air Ratchet from the air hose. Step 2: Apply a few drops of PNEUMATIC TOOL OIL through the air inlet before each use, CAUTION or every hour if used continuously. Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals in the tool. Step 3: Apply a few drops of oil to the VALVE (#6), location shown in Figure 6. Work the TRIGGER a few times to lubricate. Valve (#6) (underneath trigger) Air Inlet 123456123456123456123456123456123456123456123456123456123456 Figure 6 — Lubrication Points For technical questions, please call 1-800-444-3353. Page #11 -- SKU: 33567 REV 12/02 REV 05/04 Impact Wrench Operation Impact Wrench Operation : Set the compressor’s pressure regulator to a maximum of 90 PSI. 90 PSI is satisfactory without harming this tool. Step 2: Remove the plastic cap from the rear of the HOSE ADAPTER (#10). Step 3: Wrap the threads of the Air Coupler with pipe thread seal tape (not included). Attach the Air Coupler to the HOSE ADAPTER. Tighten the fitting. Step 4: Determine the socket size necessary for the job you need to do. Attach the appropriate 1/2” drive socket to the Impact Wrench as shown in Figure 7. Figure 7 — Attaching the Air Coupler and Socket Step 5: Connect the Impact Wrench to the air compressor’s hose. If leaking is detected, disconnect the air hose and repair before use. For technical questions, please call 1-800-444-3353. Page #12 -- SKU: 33567 REV 12/02 REV 05/04 Step 6: Select the power setting for Loosening by pushing in and turning the AIR REGULATOR (#11) located on the bottom of the Step 6: Select the power setting for Loosening by pushing in and turning the AIR REGULATOR (#11) located on the bottom of the Impact Wrench as shown in Figure 8. Use the Setting Appropriate for the When the AirRegulator is completely Job. Do Not Set the Power Setting screwed in it is at it’s lowest setting. Higher Than Needed. Damage to Air pressure increases as you push in Parts Could Result. and turn the Air Regulator. Figure 8 — Adjusting the Reverse Power Setting Step 7: Select the direction of the Wrench (forward or reverse) by pushing the REVERSE VALVE (#3) located on the handle of the Impact Wrench as shown in Figure 9. Figure 9 — Selecting Reverse Direction For technical questions, please call 1-800-444-3353. Page #13 -- SKU: 33567 REV 12/02 REV 05/04 Step 8: Press the TRIGGER (#4) to test the Impact Wrench. The Impact Wrench should spin freely as shown if Figure 10. Step 8: Press the TRIGGER (#4) to test the Impact Wrench. The Impact Wrench should spin freely as shown if Figure 10. Figure 10 — Pressing Trigger Loosening Step 1: Verify that the power level is correct for your needs and that the REVERSE VALVE (#3) has been shifted (pressed) completely to the right. If not, refer to Steps 6 through 7 under Impact Wrench Operation before proceeding. Step 2: Place your work in as clear a location as possible. Make sure the air hose will reach as far as needed without stressing any connections. Step 3: With the correct socket attached to the Impact Wrench, slide the socket over the nut or bolt. Step 4: Grip the Impact Wrench with both hands, especially with higher power settings. Make sure you are in a stable position and spread your feet shoulder-width apart. Step 5: Press the TRIGGER (#4) to loosen the bolt. WARNING The Impact Wrench May Kick Back Step 6: If the bolt will not loosen, and you are on a During Operation. If This low power setting for Loosening, try increas- Happens, Release the TRIGGER ing the power setting and attempt again. IMMEDIATELY! Step 7: If the bolt will not loosen with the Impact Wrench on a higher power setting, do not repeat attempts to loosen. You may snap the bolt or strip the threads of the stud or nut. Try another method to loosen the bolt or nut. For technical questions, please call 1-800-444-3353. Page #14 -- SKU: 33567 REV 12/02 REV 05/04 Tightening Tightening : Verify that the power level is correct for your needs and that the REVERSE VALVE (#3) has been shifted (pressed) completely to the left. If not, refer to Steps 6 through 7 under Impact Wrench Operation before proceeding. Step 2: Place your work in as clear a location as possib...

Herunterladen

Geben Sie zwei Ziffern: