Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
2. Obstructed trigger. 3. Incorrect lubrication or not enough lubrication. 4. Blocked air inlet screen (if equipped). 5. Air leaking from loose housing. 6. Mechanism contaminated. 1. Check for loose connections and make sure that air supply is providing enough air flow (CFM) at required pressure (PSI) to the tool's air inlet. Do not exceed maximum air pressure. 2. Clean around trigger to ensure free movement. 3. Lubricate using air tool oil and grease according to directions. 4. Clean air inlet screen of buildup. 5. Make sure housing is properly assembled and tight. 6. Have qualified technician clean and lubricate mechanism. Install in-line filter in air supply as stated in Setup: Air Supply. Housing heats 1. Incorrect lubrication or 1. Lubricate using air tool oil and grease during use. not enough lubrication. 2. Worn parts. according to directions. 2. Have qualified technician inspect internal mechanism and replace parts as needed. Severe air leakage. 1. Cross-threaded housing 1. Check for incorrect alignment and uneven gaps. (Slight air leakage components. If cross-threaded, disassemble and is normal, replace damaged parts before use. especially on 2. Loose housing. 2. Tighten housing assembly. If housing cannot tightenolder tools.) 3. Damaged valve or housing. 4. Dirty, worn or damaged valve. properly, internal parts may be misaligned. 3. Replace damaged components. 4. Clean or replace valve assembly. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. accessory list item/ Part* Description Function 68276 3 Piece Long Air Chisel Set Basic chisel set for bolt cutting, masonry work, and sheet metal work 68277 4 Piece Short Air Chisel Set For use in tight places for cutting, masonry work, and sheet metal work 66621 Air Hammer Quick Release Chisel Holder Quickly change chisels *Item or part number may not be available for some accessories. maintenanCe OPeRatiOnSetuP SaFetY Page 14 For technical questions, please call 1-800-444-3353. Item 92037 Part Description Qty1 Body 1 2 Rubber Gasket 1 3 O-Ring 2 4 Regulator 1 5 Control Pin 1 6 O-Ring 1 7 Ball 1 8 Spring 1 9 Air Inlet 1 10 Rear Valve 1 Part Description Qty11 Valve Disk 1 12 Front Valve 1 13 Piston 1 14 Cylinder 1 15 Retainer Spring 1 16 Trigger 1 17 Pin 1 18 Pin 1 19 Chisel 1 Parts list and Diagram PleaSe ReaD the FOllOWinG CaReFullY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Parts list Record Product's Serial number here: note: If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SaFetY OPeRatiOn maintenanCeSetuP Part Description Qty1 Body 1 2 Rubber Gasket 1 3 O-Ring 2 4 Regulator 1 5 Control Pin 1 6 O-Ring 1 7 Ball 1 8 Spring 1 9 Air Inlet 1 10 Rear Valve 1 Part Description Qty11 Valve Disk 1 12 Front Valve 1 13 Piston 1 14 Cylinder 1 15 Retainer Spring 1 16 Trigger 1 17 Pin 1 18 Pin 1 19 Chisel 1 Parts list and Diagram PleaSe ReaD the FOllOWinG CaReFullY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Parts list Record Product's Serial number here: note: If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SaFetY OPeRatiOn maintenanCeSetuP assembly Diagram maintenanCe OPeRatiOnSetuP SaFetY limited 90 Day Warranty limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality ...