Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Before use, be sure to carefully read the instructions. Read the related Drill instruction manual, too. . Be sure to wear protective goggles during work. . Be sure to wear a dust-proof mask during work. . Depending on the work environment, wear ear protectors, hardhat, working shoes, and other safety gear. . Be sure to use the specified Adaptor Kit that is dedicated to your Drill model. . Be sure to use the specified "VISROPE" connecting screws. . Ensure solid footing and hold yourself in a safety-first position. . Wear clothes proper for work. . Keep the workplace in order and well lit. . When working in an elevated place, make sure there is nobody beneath. Be very careful not to let this unit and screws fall. . Never direct this unit toward anybody. . Never keep your hands, feet and head close to the tip (screw outlet) of the unit during work. . Keep the unit away from open fire and flame. . Do not use the unit near volatile, flammable substances such as gasoline, thinner, gas, paint, and adhesive. The unit may catch fire or explode. . Do not use the unit in rain, or water-splashed, wet or humid area. Do not leave the unit in rain, either. . Keep the unit, accessories and consumable parts without reach of children. . For after-use handling, refer to "Maintenance and inspection". . Handle the unit with enough care. Dropping or hitting may result in malfunction. . Keep these instructions in the safe place. Parts designation Specifications Heavy Duty Auto Feeding Screwdriving Tool Overall length (including the handle) Approx. 885 -1,005 mm * For 45 mm screw length Weight (without the motor) Approx. 5.4 kg Max. driving depth Approx. 8 mm Applicable screw length 32 – 76 mm (1-1/4” to 3”) Applicable screw head diameter DIA 10 – 13 mm Applicable screw nominal diameter DIA 5 – 6 mm Electrical specifications See the motor instruction manual 1 Assembling VISLIDER 1. Assembly and fitting of rod handle Remove the hexagon fitting bolt and the washer Mount the assembled rod handle on the rear of the from the handle rod. To the handle rod, fit the main body. Tighten the two fitting screws using handle bar, the washer and the hexagon bolt in this the 6mm wrench. order. Tighten the hexagon fitting bolt using the 13mm spanner. 2. Fitting and removal of magazine To fit the magazine, insert the magazine holder To remove the magazine, withdraw it while pulling into the bracket at top end of the main body until the magazine stopper with fingers. it clicks. 2 Loading VISROPE 1.Setting VISROPE Open the magazine cover while pulling the Set the VISROPE to the magazine as shown magazine lever. below. (Remove the rubber band from the VISROPE.) 2. Switching magazine inner lid Lift the inner lid while holding the inner lid stopper on the magazine cover. Insert the inner lid until it snaps in the orientation corresponding to the screw length. 3. VISROPE types and stopper block adjustment Two types are available in the VISROPE for VL71-FLR, 30mm type and 22mm type. Depending on the type, the position of the guide differs and the stopper block needs to be adjusted to fit for the screws used. * The first VISROPE has an extended plastic strip as shown below, which is needed to drive the first screw. Please confirm the presence of this extension when loading. * The stopper block fixing cap screw, when loosened too much, can cause its head to protrude. Pay due attention to it. 3 * Factory setting is for 30mm type. 4. Screw guide position adjustment Carry out the screw guide position adjustment according to the length of the screws used. * Factory setting is for 45mm screw length. 5. Feeding screws Insert the VISROPE into the feeder block until it stops. Push the main body by no less than 30mm, and then pull it back. When the screw is not fed to the center even after the above step was repeated several times, carry out the guide cover adjustment by referring to 6. Adjustment of guide cover and then retry the screw feeding. 4 6. Adjustment of guide cover Improper guide cover play can affect screw feeding or screw driving. Any time the VISROPE was replaced, make sure to check the guide cover play and adjust it to the adequate level. To adjust the play, first loosen the hexagon nut using the 7mm spanner and then adjust the cap screw using the 3mm wrench. After this, tighten the hexagon nut using the 7mm spanner to fix the cap screw. Driving screws 1. Adjustment of rod handle length 2. Adjustment of screw driving depth To adjust the rod handle length, loosen the knob Turn the dial to adjust the screw driving depth. and press it with force to disengage the inside fixing tab. After this, adjust the length and tighten the knob to fix. 3. Direction of bit rotation Direction of bit rotation can be reversed using the motor forward/reverse rotation switch. Use the forward (clockwise) rotation to drive (tighten) the screw, and the reverse (counterclockwise) rotation to loosen (remove) the screw. Refer to the relative instruction manual of the motor on h...