Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Hold tool firmly and place the bit at the point to be ddlled. Depress the switchtrigger to start tool. Move the ddll bit into the workpiece applying only enough pressure to keep the bit cutting. Do not force or apply side pressure to elongate a hole. WARNING: Be prepared for binding or bif breakthrough. When these situations occur, drill has a tendency to grab and kick opposite to the direction of rotation and could cause loss of control when breaking through material. If not prepared, this loss of control can result in possible serious injury. MALLET KEYLESS CHUCK \ CHUCK JAWS HEX KEY WRENCH Fig. 12 Open chuck jaws and remove hex key wrench. Remove the chuck screw by turning it in a clockwise direction. See Figure 13. Note: The screw has left hand threads. Fig. 13 11 CHUCK REMOVAL (Continued) _i WARNING: When servicing, use only identical Insert hex key wrench in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen chuck on the spindle. It can now be unscrewed by hand. See Figure 14. Fig. 14 TO RETIGHTEN A LOOSE CHUCK The chuck may become loose on spindle and develop a wobble. Periodically check chuck screw for tight ness. To tighten, follow these steps: • Lock switch trigger on your drill by placing the direction of rotation selector in center position. See Figure 2. • Open the chuck jaws. • Insert hex key wrench into chuck and tighten chuck jaws securely. Tap hex key wrench sharply with a mallet in a clockwise direction. This will tighten chuck on the spindle. • Open the chuck jaws and remove hex key wrench. • Tighten the chuck screw. Note: The chuck screw has left hand threads. Craftsman replacement pads. Use of any other part may create a hazard or cause product damage. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. _i WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic. Do not abuse power tools. Abusive practices can damage tool as well as workpiece. Only the parts shown on parts list, page 15, are intended to be repaired or replaced by the customer. All other parts should be replaced by a qualified service technician at an authorized service facility, _ WARNING: Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. BATTERIES Your drill's battery pack is equipped with 12 nickel- cadmium rechargeable batteries. Length of service from each charging will depend on the type of work you are doing. The batteries in this tool have been designed to provide maximum trouble free life. However, like all batteries, they will eventually wear out. Do not disassemble battery pack and attempt to replace the batteries. Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn. To obtain the longest possible battery life, we suggest the following: • Store and charge your batteries in a cool area. Temperatures above normal room temperature will shorten battery life. • Never store batteries in a discharged condition. Recharge them immediately after they are discharged. • All batteries gradually lose their charge. The higher the temperature the quicker they lose their charge. If you store your tool for long periods of time without using it, recharge the batteries every month or two. This practice will prolong battery life. 12 To preserve natural resources, please recycle or dispose of batteries properly. This product contains nickel- cadmium batteries. Local, state or federal laws may prohibit disposal of nickel-cadmium batteries in ordinary trash. Consult your local waste authority for information regarding available recycling and/or disposal options. BA'I-rERY PACK REMOVAL AND PREPARATION FOR RECYCLING ,_ WARNING: Upon removal, cover the battery pack's terminals with heavy duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its components. Nickel- cadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury. 13 14 ,---CRAFTSMAN 318 In., 14.4 VOLTS CORDLESS DRILL-DRIVER -MODEL NO. 973.111291 number in all correspondence regarding your 3/8 In., 14.4 VOLTS CORDLESS DRILL-DRIVER or The model number will be found on a plate attached to the motor housing. Always mention the model | when ordering repair parts. J SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 2 \ 3 Key Part No, Number 1 61...