Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting. B 9 7 8 90544571 PD400 clutch sc 5/22/09 7:46 AM Page 6 7 ASSEMBLY AND ADJUSTMENT INSERTING AND REMOVING BITS (FIGURE C) • To install a hex shank screwdriver bit or drill bit (10) simply insert it into the cavity in the hex spindle (6) until it snaps into place as shown in figure C. • To remove the bit pull it straight out. PIVOTING THE TOOL HEAD (FIGURES D, E) The head of the tool can be pivoted for optimum versatility. • Press the pivot release button (3) shown in figure D. • Pivot the tool head to the inline position as shown in figure E. • Release the button. WARNING: Check to make sure tool handle is locked after pressing pivot release button and changing screwdriver positions. WARNING: • To avoid being pinched at the areas indicated with black arrows, hold the screwdriver at both ends and use your thumb to depress the pivot release button (3) when changing positions. • Do not use screwdriver as a pry bar in any position. • To avoid screwdriver being turned on accidentally, do not carry in your pocket. FORWARD/REVERSE/LOCK OFF SLIDER (FIGURE F) • To select forward or reverse rotation, use the forward/reverse slider (2) (see arrows on the slider). NOTE: When the slider is in the central position the tool is locked off to prevent accidental actuation or battery discharge. C D F E 2 3 10 6 90544571 PD400 clutch sc 5/22/09 7:46 AM Page 7 8 OPERATING INSTRUCTIONS Prior to operation: • Make sure your screwdriver is (fully) charged. SWITCHING ON AND OFF (FIGURE G) • To turn the tool ON in a forward direction, move the forward/reverse slider (2) upward. • Squeeze the trigger switch (1) and the tool will run. • Release pressure from the trigger and the tool will stop. • To turn the tool ON in a reverse direction, move the forward/reverse slider (2) downward. • Squeeze the trigger switch (1) and the tool will run. • Release pressure from the trigger and the tool will stop. • To lock the tool in the off position, move the forward/reverse slider (2) to the central position. TORQUE CONTROL (FIGURE H) Your screwdriver is equipped with a six position adjustable clutch collar (5). When the tool reaches the preselected torque setting the clutch slips, thus limiting how tightly a screw is driven. • The tool’s motor will continue to run as long as the switch button is depressed. • To set the tool’s torque, rotate the adjustable clutch collar (5) clockwise or counterclockwise as required. The larger the screw icon, the higher the torque. • Each click in a clockwise direction (facing the spindle ) means an increase in the torque produced. SCREWDRIVING • Insert the appropriate hex shank screwdriver bit. • Set the forward/reverse slider (2) to the desired rotation. • Set the adjustable clutch collar (5) to position 1 and begin screwdriving (low torque). • If the clutch ratchets too soon, adjust the collar to increase the torque as required. DRILLING • Insert the appropriate hex shank drill bit. • Select the drilling mode using the adjustable clutch collar (5) to the position marked with the largest screw icon. • Select forward rotation. GENERAL DRILLING TIPS • This tool is not recommended for drilling in masonry. • Use sharp drill bits only • Drill bits for metal can be used for drilling holes in wood. These bits must be sharp and should be pulled out frequently when drilling to clear chips from the flutes. • Support and secure work properly, as instructed in the safety Instructions. • Use appropriate and required safety equipment, as instructed in the safety instructions. • Secure and maintain work area, as instructed in the safety instructions. • Use light pressure until the hole is started enough to keep the drill bit from slipping out of it. • Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit. • Hold the tool firmly to control its twisting action. H 5 1 G 2 1 90544571 PD400 clutch sc 5/22/09 7:46 AM Page 8 90544571 PD400 clutch sc 5/22/09 7:46 AM Page 9 • DO NOT CLICK THE TRIGGER OF A STALLED TOOL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE TOOL CAN RESULT. To remove, twist the bit back and forth and straight out. • Minimize stalling on breakthrough by reducing pressure and slowly drilling through last part of hole. • Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming. • Make sure switch turns tool on and off. WARNING: It is important to support work properly and to hold the tool firmly to prevent loss of control which could cause personal injury. MAINTENANCE Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authori...
Dieses Handbuch ist für folgende Modelle:Bohrmaschinen und Schrauber - PD400 (2.86 mb)