Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide. CHARGING THE POWER PACK THE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE FACTORY. BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS. The charger is designed to use standard household 120 volt 60 Hz power. 1. Make sure the battery is fitted into the drill as shown in Figure 1. Insert the charger plug into the connector as shown in Figure 2. 2. Plug the charger into any standard 120 Volt 60 Hz electrical outlet and let the battery charge initially for 9 hours. After the initial charge, under normal usage, your power pack should be fully charged in 3 to 6 hours. 3. Disconnect the tool from the charger. WARNING: Do not use the tool while it is connected to the charger. IMPORTANT CHARGING NOTES 1. After normal usage, your power pack should be fully charged in 3 to 6 hours. If the power pack is run-down completely, it may take up to 6 hours to become fully charged. Your power pack was sent from the factory in an uncharged condition. Before attempting to use it, it must be charged for at least 9 hours. 2. DO NOT charge the power pack in an air temperature below 40°F or above 105°F. This is important and will prevent serious damage to the power pack. Longest life and best performance can be obtained if power pack is charged when air temperature is about 75°F. 3. While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem. 4. If the power pack does not charge properly—(1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and power pack to a surrounding air temperature of 40°F to 105°F. (4) If the receptacle and temperature are OK, and you do not get proper charging, take or send the power pack and charger to your local Black & Decker service center. See Tools Electric in yellow pages. 5. The power pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its power pack in a depleted condition. 6. To prolong power pack life, avoid leaving the power pack on charge for extended periods of time (over 30 days without use). Although overcharging is not a safety concern, it can significantly reduce overall power pack life. 7. The power pack will reach optimum performance after being cycled 5 times during normal usage. There is no need to run the batteries down completely before recharging. Normal usage is the best method of discharging and recharging the batteries. Safety Warnings and Instructions: Drills 1. Hold drill firmly to control the twisting action of the drill. See Figure 3. 2. When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly. WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall. Grip the drill firmly to control the twisting action (see Fig. 3) and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting. Operating Instructions FITTING AND REMOVING A DRILL BIT OR SCREWDRIVER BIT (FIGURE 4) WARNING: First remove the battery from the tool. This tool is equipped with a keyless chuck to allow for easy exchange of bits. • Lock the tool by setting the forward/reverse slider (2) to the center position. • Open the chuck by turning the front part (11) with one hand while holding the rear part (12) with the other (Figure 4). • Insert the bit shank (13) into the chuck. • Firmly tighten the chuck by turning the front part (11) with one hand while holding the rear part (12) with the other. SELECTING THE DIRECTION OF ROTATION (FIGURE 5) A forward/reverse control slider (2) determines the direction of the tool and also serves as a lock off. To select forward rotation, push the forward/reverse slider to the left. To select reverse rotation, depress the forward/reverse slider to the right. To lock the tool, set the forward/reverse slider into the center position. SELECTING THE OPERATING MODE OR TORQUE (FIGURE 6) This tool is fitted with a collar to select the operating mode and to set the torque for tightening screws. Large screws and hard workpiece materials require a higher torque setting than small screws and soft workpiece materials. • For drilling in wood, metal and plastics, set the collar (3) to the drilling position by aligning the symbol with the marking (15). • For screwdriving, set the collar to the desired setting. If you do not yet know the appropriate setting, proceed as follows: • Set the collar (3) to the lowest torque setting. • Tighten the first screw. • If the clutch ratchets before the desired result is achieved, increase the collar setting and continue tightening the screw. Repeat until you reach the correct s...