Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
To avoid stress on the drill bit, try extending your index finger along the side of the drill-housing with your middle finger on the trigger. Remember—guide, the tool, don't force it! Should the tool become overheated, run it with no load. Because of the drill's construction, it will cool faster running than by stopping it. DULLING IN METAL Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry. The cutting lubricants that work best are sulphurized cutting oil or lard oil; bacon grease will also serve the purpose. Aluminum is best drilled with turpentine or kerosene. DRILLING IN WOOD Holes in wood can be made with the same twist drills used for metal. These bits may overheat unless pulled out frequently to clear chips from the flutes. - For larger holes, use Power Drill Wood Bits with a shank size that will fit your drill's chuck. Work that is apt to splinter should be backed up with a block of wood. Let up on the pressure fust before the tip cuts through, this will give a good clean hole. Always leave the drill running when pulling it back out of a drilled hole* this prevents jamming. TO REMOVE CHUCK for using a threaded shank accessory, first insert key into chuck key hole. Then strike the key sharply with a piece of wood in the direction the chuck rotates when the Drill is turned "ON." This will loosen the chuck shank threads and the chuck may be unscrewed from the Drill. LUBRICATION Self lubricating bearings are used in the tool and periodic relubrication is not required. However, it is recommended that, at least once a year, you take or send the tool to a B&D Service Center for a thorough cleaning, inspection and lubrication of the gear case. GUARANTEE Black & Decker guarantees, for one year from date of purchase, to correct by repair or parts replacement without charge any defect due to faulty material or workmanship. Simply return the complete unit, transportation prepaid, to any Black & Decker Service Center or Authorized Service Station. Naturally, we assume no responsibility for damage caused by misuse, careless handling or where repairs have been made or attempted by others. No other guarantee, written or verbal, is authorized by us. IMPORTANT! To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by BLACK & DECKER Service Centers or other qualified service organizations, always using BLACK & DECKER replacement parts. See'Tools-Electric’ —Yellow Pages— for Service & Sales THE BLACK & DECKER MFG. CO., TOWSON, MD. 21204, U.S.A. Form No. 97142 (B5-AL) Printed in U.S.A. Ill OWNER’S MANUAL DRILL *1000 Capacity: y4” holes in steel; y2” in hardwood. 115 Volts A.C. 1.9 Amps. 1/7 H.P. 2250 R.P.M. 3/s" DRILL #1101 Capacity: %" holes In steel; in hardwood. 115 Volts A.C. 2D Amps. 1/7 H.P. 1000 R.P.M. Blacks Decker. N05.10ОО AND 1101 DRILLS ^P.T.I. SAFETY RULES FOR POWER TOOLS 1. ■' KNOW YOUR POWER TOOL—lead owner's manual carefully., Learn its applications.:and limitations as well as the specific potential hazards peculiar to this tool, 2. GROUND ALL TOOLS — UNLESS- DOUBLE-INSULATED. .If tool is equipped with three-prong plug, it should be plugged into a three-hole electrical reeeptable. If adapter is used to accommodate two*prong receptacle, the adapter wire must ' be attached- to a known ground. Never remove third prong, 3. . KEEP GUARDS IN PLACE and in working order. 4. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 5. 'AVOID DANGEROUS ENVIRONMENT. Don't use power tool in damp or wet locations. And keep work area well Sit. 6. KEEP CHILDREN AWAY, All visitors should be kept safe distance from work area. 7. STORE IDLE TOOLS« When not in use, tools should be stored in dry, high or locked-up place — out of reach of children. . g DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed. . 9. USE RIGHT TOOL. Don't force small tool or attachment to do the job of a heavy duty tool. 10. WEAR PROPER APPAREL. No loose clothing or jewelry to get caught In moving parts. Rubber gloves and footwear are ■ ^ recommended when working outdoors. 11. USE SAFETY GLASSES with most tools. Also face or dust mask if cutting operation is dusty. 12. DON'T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle.: Keep cord from heat, oil and sharp edges. 13. SECURE WORK. Use clamps or a vise to hold work. It's safer than using your hand and it frees both hands to . operate tool. 14. DON'T OVERREACH. Keep proper footing and balance at all times. 15. MAINTAIN TOOLS WITH CARE. Keep tools sharp at all times, and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 16. DISCONNECT TOOLS. When not in use, before servicing, when changing accessories such as blades, bits, cutters, etc. 17. REMOVE ADJUSTING 'KEYS AND WRENCHES. Form' habit of checking to see that keys and adjusting wr...