Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
4. If the batteries do not charge properly: (1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power offwhen you turn out the lights. (3) Move charger and tool to a surrounding air temperature of above 40 degree F(4,5°C) or below 105 degree F (+40,5°C). (4) If the receptacle and temperature are okay, and you do not get proper charging, refer to your warranty. 5. The tool should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its batteries in adepleted condition. 6. To prolong battery life, avoid leaving on charge for extended periods of time (over 30 days without use). Although overcharging is not a safety concern, it can significantlyreduce overall battery life. 7. The batteries will reach optimum performance after being recharged 5 times during normal usage. There is no need to run the batteries down completely beforerecharging. Hanging the Charging Base (fig. 2 & 3) Use the hardware provided only if hanging on conventional hollow wall construction such as sheet rock or plaster walls. If not hanging on conventional sheet rock or plaster walls, please use the appropriate fasteners for that material. The charger can be fixed to the charger mounting bracket as described below, or simply placed, in a convenient level position. • Locate the charger mounting bracket within reach of an electrical outlet. • Mark the position of both hang holes as shown in figure 2. • The mounting screws should be driven in to about an 1/8” (3mm) from the wall. • Place the charger mounting bracket over the screw heads and slide down until fully seated. • Finish tightening the screws and check to see that the bracket is firmly attached to the wall so it will not pull out. • Place the charger in position until it “clicks” into place as shown in figure 3. Safety Warnings and Instructions: Drilling 2 3 • Hold tool firmly to control its twisting action. WARNING: Tool may stall (if overloaded or improperly used) causing a twist. To reduce the risk of injury always expect the stall. Grip the tool firmly to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting. 5 90503227 ISD600 Impact Driver 6/15/06 12:52 PM Page 6 OPERATING INSTRUCTIONS Quick Release Chuck To install an accessory: • Hold the tool as shown in figure 4 and push the chuck collar away from the tool. • Insert a hex shank accessory and release the collar. • The accessory is locked in place. NOTE: Do not insert a bit tip into the tool without using a bit tip holder (not provided). To remove an accessory: • Hold the tool as shown in figure 4 and push the chuck collar away from the tool. • Remove the accessory and release the collar. Switch • To turn the tool ON in a forward direction, hold the tool as shown in figure 5, press the top section of the rocker switch and the tool will run. • Release pressure from the switch and the tool will stop. • To operate in reverse, press the bottom section of the rocker switch. Without depressing the rocker switch the tool is locked and will act as any conventional, non-powered driver. NOTE: The unit will make a “ratcheting” noise when the impact mechanism engages. This is normal and does not indicate a problem. 4 5 Impact Driver Warnings: • Hold the tool as shown in figure 5. • Do not use tool as a pry bar. • To avoid being turned on accidentally, do not carry in your pocket. Drilling • Use sharp drill bits only. • Drill bits for metal can be used for drilling holes in wood. These bits must be sharp and should be pulled out frequently when drilling to clear chips from the flutes. • Support and secure work properly, as instructed in the safety Instructions. • Use appropriate and required safety equipment, as instructed in the safety instructions. • Secure and maintain work area, as instructed in the safety instructions. • Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it. • Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit. • Hold the tool firmly with two hands to control its twisting action. • DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT. To remove twist the bit back and forth and straight out. • Minimize stalling on breakthrough by reducing pressure and slowly drilling through last part of hole. • Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming. • Make sure switch turns tool on and off. WARNING: It is important to support work properly and to hold the drill firmly to prevent loss of control which could cause personal injury. M...
Dieses Handbuch ist für folgende Modelle:Bohrmaschinen und Schrauber - ISD600 (384.57 kb)