Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Hitachi Dateigröße: 2.64 mb Dateiname: e9d86962-4221-82c4-9136-415103912721.pdf Unterrichtssprache:

Injury may result if you carry the equipment suspended from the waist belt with sharp tipped components such as drill bit attached. 4(B) Fig. 7321 5 The hook can be installed on the right or left side and the angle can be adjusted in 5 steps between (A) 0° and 80°. Hook (1) Operating the hook (a) Pull out the hook toward you in the direction of arrow (A) and turn in the direction of arrow (B). (Fig. 7) (b) The angle can be adjusted in 5 steps (0°, 20°, 40°, 60°, 80°). Adjust the angle of the hook to the desired position for use. (2) Switching the hook position Loosen CAUTION: . If the tool falls, there is a risk that malfunction and/ or physical damage can occur. It is recommended that you also use fall-preventing wires, etc. . Incomplete installation of the hook may result in bodily injury when used. (a) Securely hold the main unit and remove the screw using a slotted head screwdriver or a coin. (Fig. 8) (b) Remove the hook and spring. (Fig. 9) (c) Install the hook and spring on the other side and securely fasten with screw. (Fig. 8) Fig. 9 NOTE: Pay attention to the spring orientation. Install the spring with larger diameter away from you. (Fig. 10) 1.1 Using the bit holder (Hook with bit holder) . Installing the bit Slide the bit from the side, and then insert firmly until the groove on the bit locks in the protruded section of the hook. . Removing the bit Securely hold the main unit and pull out the bit by holding the tip with your thumb. (Fig. 11) CAUTION: . Only Hitachi STANDARD ACCESSORIES phillips bit (No. 2 . 65L; Code No. 983006) may be used. Do not use other bits since they may come loose. Hook Screw Fig. 8 Spring Screw Larger diameter faces away Fig. 10 Fig. 11 batteries Hook cover batteries Hook cover English 1.2 Using as an auxiliary light (Light equipped hook) (1) Press the switch to turn off the light. If forgotten, the light will turn off automatically after 15 minutes. (Fig. 12) (2) The direction of the light can be adjusted within the range of hook positions 1 - 5. (Fig. 7) . Lighting time AAAA manganese batteries: approx. 15 hrs. AAAA alkali batteries: approx. 30 hrs. CAUTION: . Do not look directly into the light. Such actions could result in eye injury. 1.3 Replacing the batteries (Light equipped hook) (1) Loosen the hook screw with a phillips-head screwdriver (No. 1). (Fig. 13) Remove the hook cover by pushing in the direction of the arrow. (Fig. 14) (2) Remove the old batteries and insert the new batteries. Align with the hook indications and position the plus (+) and minus (-) terminals correctly. (Fig. 15) (3) Align the indentation in the hook main body with the protuberance of the hook cover, press the hook cover in the direction opposite to that of the arrow shown in Fig. 14 and then tighten the screw. Use commercially available AAAA batteries (1.5 V). NOTE: Do not tighten the screw excessively. Such action could strip the screw threads. CAUTION: . Failure to observe the following can result in battery leakage, rust or malfunction. Position the plus (+) and minus (-) terminals correctly. Replace both batteries at the same time. Do not mix old and new batteries. Remove exhausted batteries from the hook immediately. Switch Hook Fig. 12 Hook Phillips-head screwdriver Arrow Hook cover Screw Fig. 13 Fig. 14 Hook main body Inden- Protube tation rance AAAA Protuberance Indentation Fig. 15 . Do not discard batteries together with normal trash and do not throw batteries into fire. English . Store batteries out of the reach of children. . Use batteries correctly in accordance with the battery specifications and indications. 2. Using the bit holder CAUTION: Bit . Stow the bit in the specified location on the tool. If the tool is used with the bit stowed improperly, the bit may fall and cause bodily injury. . Do not stow bits that are of a different length, gauge or dimension than the plus driver bit (65 mm long) included in the STANDARD ACCESSORIES. The bit may fall and cause bodily injury. (1) Removing the bit Securely hold the main unit and pull out the bit by holding the tip with your thumb. (Fig. 16) (2) Installing the Bit Install the bit with steps opposite of when removing. Insert the bit so that the right and left sides are Insert so that equal, as shown in Fig. 17. bit does not protrude 3. Installing/Removing the side handle from main unit Fig. 17 CAUTION: . Firmly install the side handle. If loose, the side handle may gyrate or fall out and cause bodily injury. (1) Install the side handle so that the protrusions on Side the main unit and grooves on the side handle interlock. Tighten the grip after checking that the side handle is not riding on the slip prevention protrusion. (Fig. 18) Loosen (2) Loosen the grip to remove the side handle. 4. Mounting and dismounting the bit Grip (1) Mounting the bit Loosen Loosen the sleeve by turning it toward the left (in the counterclockwise direction as viewed from the front) to open the clip on the keyless chuck. After inserting a driver bit, e...

Herunterladen

Geben Sie zwei Ziffern: