Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung King Canada, modell H7794

Hersteller: King Canada
Dateigröße: 1.18 mb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

2. Insert the battery into the charger. The battery fits into the oval recess in only one way. Do not force the battery. Insert until it locks into place. Note: Allow the battery to cool down before charging. After charging is completed, allow the battery to cool down before installing it in the drill. 3. The red light will come on (Models H7792/3 will blink slowly) when the battery is charging. Charge the battery for 1 hour or until the charging light turns green (Models H7794/5) or blinks rapidly (Models H7792/3). After several hours the light will turn off and the unit will stop charging. Note: It is normal for the battery and charger to become warm during charging. 4. Remove the battery when fully charged and unplug the charger. Never leave a battery unattended while charging to prevent a chance offire.Disconnectthecharger immediately if the battery or char- gerbecomestoohottotouch, then have the battery and charger checkedbyaqualifiedelectrical service technician. Model H7792/H7793/H7794/H7795 Cordless Drills -9 Direction Switch Installing Bits The direction switch can be placed in the center position to prevent the drill from operating, to the right for clockwise bit rotation, or to the left for counterclockwise rotation. To set the drilling rotation: 1. To place the direction switch (Figure 2) in the lock (center) position, push the switch until it protrudes equally from both sides of the drill. This drill is intended for use with drill bits or screwdriver bits with up to 3.8" shanks. To install a bit: 1. Place the direction switch in the lock (center) position. 2. Hold the chuck by the collar while turning the sleeve (Figure 3) to open or close the chuck jaws. Figure 2.Direction switch. Figure 3.Inserting a bit into the chuck. Chuck Sleeve Chuck Collar 2. Adjust the jaws to the approximate 2. Push the direction switch in from the diameter of the bit or driver and insert right side for clockwise rotation (for- the shank into the chuck. ward). 3. Turn the sleeve clockwise to tighten the 3. Push the direction switch from the chuck around the bit or driver. Check left side for counterclockwise rotation the tightness periodically while using (reverse). the tool. 4. Pull the trigger and look at the lighted Note: “Power tightening” (holding the arrows on the top of the drill to confirm sleeve while running the drill) can direction. cause a loose grip on the bit or driver and potential damage to chuck jaws. 4. To release the bit or driver, hold the chuck collar, and turn the sleeve counterclockwise. Note: The bit may be hot after use. Use gloves when removing. -10- Model H7792/H7793/H7794/H7795 Cordless Drills Torque Settings The clutch is designed to slip at a preset torque to prevent damage to the tool or the screw, and to prevent driving screws too deep. Use lower torque settings for screwing into soft materials with short screws, and higher settings for harder materials and longer screws. The clutch does not slip when set in the drill position. To adjust the torque: 1. Rotate the clutch ring shown in Figure 4 to adjust the torque. The clutch will slip easiest in the number 1 setting; the torque increases as the number increases. Clutch Ring Figure 4. Torque adjustment clutch ring. 2. Turn the clutch ring to the drill setting to prevent the clutch from slipping. Note: DO NOT operate the drill with the clutch set between the highest number and the drill setting. The clutch mechanism may be damaged. When the clutch is in the drill posi- tion,thedrillcantwistseverely, causing a sprained wrist or pinching your hand between the drill and a solid object. Hold the drill with both handsand be aware of the drill posi- tion to prevent injury. Driving Screws Operatingthisequipmenthasthe potential for flying debris to cause eye injury. Always wear safety glasses or goggleswhenoperatingequipment. Everydayglassesorreadingglass- es only have impact resistant lenses, they are not safety glasses. Be certain the safety glasses you wear meet the appropriate standards of the American National Standards Institute (ANSI). Use the lowest possible torque setting when driving fasteners to prevent damage to the screw, and to prevent driving screws too deep. To drive screws: 1. Install a screwdriver bit that matches the screw head pattern. 2. Set the torque to an appropriate setting for the workpiece and set the direction to clockwise (forward). 3. Place the screwdriver bit into the screw and the screw firmly against the workpiece, start the drill slowly and gradually increase speed, while applying pressure to drive the screw into the workpiece. Note: You may wish to drill a pilot hole before driving the screw, depending on the workpiece and screw type. To remove screws: 1. Set the direction to counterclockwise (reverse) and the clutch to the highest torque setting. 2. Place the screwdriver bit into the screw, pull the drill trigger, and push lightly to keep the bit in the screw. Model H7792/H7793/H7794/H7795 Cordless Drills -11 D...