Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Global Machinery Company Dateigröße: 532.53 kb Dateiname: Unterrichtssprache:

Set Button 2. Temperature and Clock Time Increase Button 3. Temperature and Clock Time Decrease Button 4. Real-time Heating Indication 5. Medium Warm Indication 6. Night Power Indication 7. Heating Power Indication Area 8. Heating Indication 9. Delay Indication 10. Intelligent Indication 11. Mode Button 12. Power Level Selection Button 13. On/Off Button 14. Warm Keeping Indication 15. 2 Indication 16. Clock Time Display 17. Temp.Setting / Actual Temp Display 18. 1 Indication Time Time Signaling Indication Real-time Heating Indication Medium Warm Indication Night Power Indication Intelligent Indication Delay Indication Mode Power Set Confirm 850 W 1300 W 2150 W TIME 1 TIME 2 Remote Controller Panel Illustration For the first use after installation, due to there's no water within the tank, first the city water inlet valve and mixing valve must be opened. Close the mixing valve when water flows out continuously from the showerhead or other outlets (the tank is full). Check connections are free of water leakage, and insert the power plug. 1. Powering On This product has a power failure memory function, i.e. it remembers temperature setting, power level, clock and current working status. Upon connecting power, all indications on the display are displayed for 2 s before the system goes into standby status (with only clock display and all buttons except On/Off button inactive) or previous working status before power failure with corresponding indicators lighted on. For example, machine as shown in Fig. 6 is in standby status with only On/Off button active. Operation Instructions Installation Installation must be made by installers of or designated by our company after-service department. The water heatershall be wall-mounted. Before installation, make sure water heater rear wires are fit firmly. Determine an installation location. Make four holes 12mm, 65 mm deep in the wall with an impact drill as shown in Fig. 2. Insert and fixexpansion hooks and expansion bolts in corresponding wall holes. Lift the water heater. Insert wall rack onto the hooks and bolts. Fit flat washers, rear wires and nuts in turn onto the bolts (see Fig. 3). Tighten the nuts and check them firm. Install accessories such as safety valve, drain hose as shown in Fig. 4. Use sealing compound to prevent water leakage. (Fig.2) L1 L2 (Fig.3) To facilitate installation and removal, it is suggested a G 1/2" movable nut is fitted at appropriate locations on inlet and outlet pipes respectively. Find water supply location. Connect inlet pipe, outlet pipe and city water pipe respectively to the use point. Fill the tank full of water and check if water circuit shows any leakage. For any leakage, reconnection shall be made. Cold water inlet Hot water outlet Safety valve Mixing valve Showerhead Connect to drain hose (Fig.4) (Fig.5) Note: Make sure the wall rack is reliably hung on the hooks before releasing your hands. Otherwise, the water heater may fall and cause human injury or property loss. Capacity 50L 60L 80L 100L L1 L2 320mm 320mm 320mm 320mm 230mm 300mm 282mm 370mm Connection and Use of Safety Valve: The safety valve should be connected to the cold water inlet pipe. Please check carefully if the direction is correct after installation. The correct direction of installation is that the arrowhead on the safety valve should be pointed to the water heater. Please connect the drain hose to the safety valve. Connect one end of the hose to the safety valve vent and the other end to the sewage drain. The hose can be cut short or extended as necessary. The hose shall be installed as inclined downward. The water may drip from the discharge pipe of the pressure relied device and that this pipe must be installed in a continuously downward direction and in a frost-free environment. Check safety valve once a month as follow: move the small handle of safety valve, if there's water flowing out, safety valve is normal; if there's no water flow, please contact local after-sales service station. The pressure relief device is to be operated regularly to remove lime deposits and to verify that it is not blocked. 1. Indication Area 2. Mode selection Button 3. 4. Set Button 5. 6. On/Off Button 7. Confirmation Button 8. Temperature and Clock Time Increase Button Temperature and Clock Time Decrease Button Power Level Selection Button ...

Herunterladen

Geben Sie zwei Ziffern: