Stimmen - 4, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Insert the cartridge fully into the port so that it rests on the charger port floor. The charging light will come on and charg- ing will begin. If the charging light does not come on, press the reset button. If the charging light goes out within 10 seconds even after pressing the reset button a couple of times, the battery cartridge is dead. (CAUTION: Wait for more than 5 seconds after the charging light goes out to press the reset button again.) Replace it with a new one. When the charging light goes out after about one hour, you may remove the fully charged battery cartridge. After charging, unplug the charger from the power source. CAUTION : 0 Your new battery cartridge is not charged. You will need to charge it before use. 0 If you try to charge a cartridge from a just-operated tool, sometimes the charging light will not come on. If this occurs, let the cartridge cool off for a while. Then re-insert it and try to charge it once more. When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it almost completely a couple of times. 0 If you wish to charge twobattery cartridges, allow 15 minutes between chargings on the fast charger. Installing socket adapter When you wish to use a smaller size socket, install the socket adapter. To install it, insert the socket adapter into the socket in the tool, making sure that the tightening direction matches the arrow on the tool. To loosen the nut or bolt, turn the tool over (upside-down) and insert the socket adapter into the socket in the tool. Socket adapter I Switch action To start the tool, simply depress the switch lever. Release the switch lever to stop. I Switch lever CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch Jever actuates properly and returns to the "OFF" position when released. Operation 3 1. Motor-driven semi-tightening operation Make sure that the tightening direction matches the arrow on the tool. Hold the tool bv the orir, area and dace the socket over the nut or bolt. Turn the tool on and continue to tighten until -. ' the torque limiter actuates, then turn the tool off CAUTION : When operating the tool, be sure to place the socket over the nut or bolt securely. 2. Final manual tightening operation Standard Tightening Socket bolt Size torque size After turning the tool off, perform the 11 5 kg . cm final manual tightening operation by M8 13 mm (8.3 ft . Ibs.) pulling on the tool grip in the same 230 kg . cm tightening direction. M10 (16.6 ft. Ibs.) l7mm The maximum size of standard bolts 400 kg . cm M12 (28.9 ft . Ibs.) l9mm that can be tightened with this tool is 115kg.cm 1/2" (socketsize: 13/16'). Refer to the 5/16" 9/16" (8.3 ft . Ibs.) table for the correct tightening torque 185 kg . cm 3/8" and check the torque with a torque (13.4 ft . Ibs.) 21132" 296 kg . cm wrench. 711 6" 121.4 ft . Ibs.) 3/4" 439 kg . cm 112" I I (31.7 ft . Ibs.) 13/16" CAUTION : *When performing the final manual tightening operation, be sure to hold the grip area of the tool. *Avoid the following abusive techniques. They can cause the nut or bolt to break as well as cause tool damage. I) Gripping toward the end of the tool. 11) Stepping on the tool. Ill) Strongly applying your weight to the tool. IV) Attaching a pipe or bar to the end of the tool to create more force on the tool. 0 During final tightening, if your hand does not feel an increasing force on the nut or bolt as you pull, the nut or bolt may already be tightened excessively. The nut or bolt may be very close to breaking. Replace the nut or bolt with a new one. 3. Loosening operation To loosen the nut or bolt, turn the tool over (upside-down). Loosen the nut or bolt by pulling on the tool grip manually in the loosening direction. Then turn the tool on to quickly and efficiently remove the nut or bolt. MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESS0 RIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. e Fast charger e Battery cartridge 7000 Model DC7100 Part No. 632002-4 *Charger 12V for car Battery cover Model DC7112 Part No. 414938-7 e Socket adapter 9.5 e Socket adapter 12.7 (Square drive size 3/8") (Square drive size 1/2") Part No. 785404-4 Part No. 785403-6 e Battery holster Holster holds extra battery. Part No....