Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Makita Dateigröße: 128.94 kb Dateiname: 31782bf0-1016-7e44-3d50-6eee3220b64f.pdf Unterrichtssprache:

Table 1: RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 9. Do not operate charger with damaged cord or plug - replace them immediately. 10. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. 11. Do not disassemble charger or battery cartridge; take it to a qualified serviceman when service or repair is required, Incorrect reassembly may result in a risk of electric shock or fire. 12. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. 13. The battery charger is not intended for use by young children or infirm persons without supervision. 14. Young children should be supervised to ensure that they do not play with the battery charger. 15. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 16. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when (1) Do not touch the terminals with any temperature is BELOW 10°C (50°F) or conductive material. ABOVE 40°C (104°F). (2) Avoid storing battery cartridge in a 2. Do not attempt to use a step-up trans-container with other metal objects former, an engine generator or DC power such as nails, coins, etc. receptacle. (3) Do not expose battery cartridge to 3. Do not allow anything to cover or clog the water or rain. charger vents. A battery short can cause a large current 4. Always cover the battery terminals with flow, overheating, possible burns and the battery cover when the battery car-even a breakdown. tridge is not used. 6. Do not store the tool and Battery Car5. Do not short the battery cartridge: tridge in locations where the temperature may reach or exceed 50°C (122°F). 7. Do not incinerate the Battery Cartridge 8. Be careful not to drop, shake or strike bat- even if it is severely damaged or is com-tery. pletely worn out. The battery cartridge can 9. Do not charge inside a box or container of explode in a fire. any kind. The battery must be placed in a well ventilated area during charging. SAVE THESE INSTRUCTIONS FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 002050 Installing or removing battery cartridge • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. • To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. • Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. 002063 Charging Plug the battery charger into the proper AC voltage source. Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the charger. Insert the cartridge fully into the port so that it rests on the charger port floor. 3. When the battery cartridge is inserted, the charging light 1. Button 2. Battery cartridge 1 2 1. 2. 1. Battery cartridge 2. Charging light 3. Battery charger 1 2 3 color will flash in red color and charging will begin. 4. When charging is completed, the charging light goes out. 5. If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its “trickle charge (maintenance charge)” mode. 6. After charging, unplug the charger from the power source. NOTE: • The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer’s batteries. • When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. • When you charge a battery cartridge from a just operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, let it cool off. Then re-insert it and try to charge it once more. • When you charge a battery cartridge which has not been used for a long period, sometimes the charging light will go out soon. If this occurs, remove t...

Herunterladen

Geben Sie zwei Ziffern: