Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Makita Dateigröße: 502.35 kb Dateiname: Unterrichtssprache:

Do not change the plug in any way. , VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user -as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. SAVE THESE INSTRUCTIONS. ADDITIONAL SAFETY RULES 1. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 2. Hold the tool firmly. 3. Keep hands away from rotating parts. 4. When driving into walls, floors or wherever "live" electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by the insulated grasping surfaces to prevent electric shock if you drive into a "live" wire. 5. Do not touch the bit or the workpiece immediately after operation: they may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS. Removing or installing locator assembly To remove the locator assembly, pull the locking sleeve forward and then turn it counterclockwise. Locking sleeve-, Locking position To install the locator assembly, screw it clockwise and then push the locking sleeve back in lightly toward the motor. Turn the locking sleeve slightly to match the locking positions and then push in firmly to lock the locator in place. I Locator \ I1 Removing or installing bit CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing bit. After removing the locator assembly, pull ' firmly to remove the magnetic bit holder. Hold the magnetic bit holder in your hand and grasp the bit with a pair of pliers. Pull the bit out of the magnetic bit holder. Sometimes, it helps to wiggle the bit with the pliers as you pull. Locator Bit To install the bit, follow the removal procedures in reverse. Depth adjustment Pull the locking sleeve forward and then turn it to adjust the depth. Locking position Gear housing Initially, adjust the locator assembly to create a distance of approximately 1 mm (3/64") from the tip of the locator to the base of the screw head. One full turn of the locator equals 1.5 mm (1/16") change in depth. After adjusting the locator assembly, push the locking sleeve in to lock the locator in place. Drive a trial screw into your material or a piece of duplicate material. If the depth is not suitable for the screw, continue adjusting until the proper depth setting is obtained. 1 mm (3/64") 1 mm (3/64") It-- r < Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the Trigger switch trigger fully, then release it. Lock button CAUTION : Before plugging in the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. NOTE : Even with the switch on and motor running, the bit will not rotate until you fit the point of the bit in the screw head and apply forward pressure to engage the clutch. Reversing switch action This tool has a reversing switch to change the direction of rotation. Move the revers- ing switch lever to the & position for clockwise rotation or the .& position for counterclockwise. Reversing switch lever 1 CAUTION : Always check the direction of rotation before drilling. .Use the reversing switch only when the tool comes to a complete stop. Changing the direction of rotation before the tool stops may ruin the tool. Operation Fit the screw on the point of the bit and place the point of the screw on the surface of the workpiece to be fastened. Apply pressure to the tool, Start the tool slowly and then increase the speed gradually. Withdraw the tool as soon as the clutch cuts in. CAUTION : 0 Use the proper bit for the head of the screw that you wish to use. 0 When fitting the screw onto the point of the bit, be careful not to push in on the screw. If the screw is pushed in, the clutch will engage and the screw will rotate suddenly. This could damage a workpiece or cause an injury. 0 Do not continue unnecessary clutching operation. NOTE : Make sure that the bit is inserted straight in the screw head, or the screw and/or bit may be damaged. MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, reparis, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manu...

Herunterladen

Geben Sie zwei Ziffern: