Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Makita Dateigröße: 686.55 kb Dateiname: 6070.pdf Unterrichtssprache:

Do not touch the drill bit or the workpiece immediately after operation, they may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS. Charging Uncap the charging connector hole. Connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Charging takes 3hours. CAUTION: 0 The battery in your new tool is not fully charged. You will need to charge it before use. 0 Do not operate the tool during charging. 0 Overcharging more than 2 days considerably shortens the battery service life. Always unplug the charger after completing the charge. Then cap the charging connector hole. 0 When you charge a new tool or a tool which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the tool fully after discharging it almost completely a couple of times. Selecting correct Phillips bit Nominal Diameter (mm) Use the chart to determine the best size Bit No. Wood Screw driver bit for the size of screw that you wish to use. 2.1-2.7 (3132 -1/8”) No. 2 3.1 -4,5(1/8”-3/16) Selecting slotted bit Use a slotted bit that properly fits the screw slot. Use of a bit that is too small will damage the screw and/or bit. Installing or removing driver bit CAUTION: When installing or removing the bit, be careful not to touch the trigger switch. To install the bit, place it in the chuck as far as it will go. Tighten the chuck by hand. Place the chuck key in each of the three holes and tighten clockwise. Be sure to tighten all three chuck holes evenly. To remove the bit, turn the chuck key coun- terclockwise in just one hole, then loosen the chuck by hand. 1 Chuck key Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the reversing switch to the right for clockwise rotation or to the left for counterclockwise. Reversing switch - CAUTION: 0 Always check the direction of rotation before operation. 0 Use the reversing switch only when the tool comes to a complete stop. Changing the direction of rotation before the tool stops may ruin the tool. Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work is prolonged. Wait 20-30 seconds before resuming operation. Holding tool Hold the tool as shown in the figure. When drilling a large diameter hole, hold the tool firmly with both hands. a Bubble level Thistool is equipped with a bubble level to aid in holding the tool horizontally. Simply center Bubble level the bubble in the sight window. 7 Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed grad- ually. Release the trigger just as the screw bottoms out. The electric brake will then stop the tool immediately, preventing the screw and/or bit from being damaged. NOTE: 0 Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. When driving wood screws, predrill pilot Nomlnal dlameter of Recommendedsize wood screw (") of pilot hole (mm) holesto make driving easier and to prevent 20-22 splitting of the workpiece See the chart. 3 1 (118) I (5164-3/32) I 2.2 -2.5 3.5 (9164) (3132 -3132) I 2.5 -2.8 3.8 (5132") (3132 -7/64) I 2 9 -3.2 4.5 (11164") (7164-118) 9 Storage of driver bit When not using the driver bit, return it to the storage cavity on the bottom of the tool. Drilling operation 0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. 0 Drilling in metal To prevent the bit from slipping when start- ing a hole, make an indentation with a centerpunch and hammer at the point to be drilled. Place the point of the bit in the Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry. CAUTION: 0 Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressurewill only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool. 0 There is a tremendous force exerted on the toolibit at the time of hole breakthrough. Hold the tool firmly and exert care when the bit begins to break through the workpiece. 0 Astuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly. 0 Always secure small workpieces in a vice or similar hold-down device. MAINTENANCE CAUTION: Always be sure that the tool is switched off before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance and adjustment sho...

Herunterladen

Geben Sie zwei Ziffern: