Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Makita Dateigröße: 725.56 kb Dateiname: 8400.pdf Unterrichtssprache:

To start the tool, simply pull the trigger. Release the trigger to stop. When the re- versing switch lever is in the neutral posi- * tion, the tool will not start even if you pull the trigger. CAUTION : 0 Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. 0 Always check the direction of rotation before drilling. *Use the reversing switch lever only when the tool comes to a complete stop. Changing the direction of rotation before the tool stops may ruin the tool. . When not operating the tool, keep the reversing switch lever in the neutral position. Hammer drilling operation Position the bit at the location for the hole, then pull the trigger. Do not force the tool. Light pressure gives best results. Keep the tool in position and prevent it from slipping away from the hole. Do not apply more pressure when the hole becomes clogged with chips or particles. Instead, run the tool at an idle, then re- move from the hole. By repeating this several times, the hole will be cleaned out. Drilling operation 0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. 0 Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a center- punch and hammer at the point to be drilled. Place the point of the bit in the indenta- tion and start drilling. Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry. CAUTION: 0 Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pres- sure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool. .There is a tremendous force exerted on the tool/bit at the time of hole breakthrough. Hold the tool firmly and exert care when the bit begins to break through the workpiece. 0 A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hole it firmly. .Always secure small workpieces in a vise or similar hold-down device. Selecting correct Phillips bit Nominal Diameter (mm) Use the chart to determine the best size Bit No. Wood screw driver bit for the size of screw that you wish to use. 2.1-2.7 (3/32"-1/8") No. 2 3.1-3.8 (1/8" -5/32") CAUTION : If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. . ACCESSOR IES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Fast charger Model DC9700 0 Makita Battery cartridge 9000 (9.6 V) 1-hour fast charge nickel cadmium battery Part No. 632007-4 0 Tool holster has some bits storage space. Use holster to carry drill only after removing bit. Also, keep the reversing switch lever in neutral position when carrying in the holster. Part No. 823033-38 0 Battery holster Holds with extra battery Part No. 823033-30 0 Charger 12V for car Model DC9112 oChuckkeyS10 Part No. 763415-9 0 Tool carrying case Part No. 823098-8 0 Keyless drill chuck Part No.192034-8 10 o~t-06 'a7 us 10 mm (3/8") CORDLESS HAMMER DRILL Model 84000 Note: The switch and other part conflguratlons may differ from country to country MODEL 84000 Oct -06 '87 US ITEM NO. DESCRIPTION ':\M DESCRIPTION AtD NO USED MACHINE 1 1 i pan Head screw ~5~18 Drill Chuck S10 Rubber Plate Guide Plate 18 19 20 21 I 1 1 1 D"SI Cover Plane Bea.,ng 4 Gear 17-76 Plane Bear,ng 4 5 1 Spindle 22 1 Pin 6 6 1 Clutch Cam 23 1 Change Lever 7 1 Comprerrlo" Spring 17 24 1 Rubber Plug 8 1 Retal"e, 25 1 Rubber Plug 9 1 Plane Bearing 6 27 1 Name Plate 10 1 Motor 28 1 Holder 6 11 1 Steel Ball 4 8 29 1 Housing Set IWith Item 131 12 1 Compression Spring 4 30 1 Battery 9000 19 6 V I 13 1 Housing Set IWith Item 291 31 1 Set Plate 17 1 Switch 32 a Pan Head Screw M4x22 IWith Washer1 Note The Switch and other part specifications may differ from country to country .. MAKmA LIMITEDONE YEAR WARRANTY Warranty Policy Every Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted to be free of defects from wor&iship and materials for the period of ONE YEAR from the date of original purchase. Should any ...

Herunterladen

Geben Sie zwei Ziffern: