Stimmen - 0, Durchschnittliche Bewertung: 4 ( )

Hersteller: Harbor Freight Tools Dateigröße: 1.37 mb Dateiname: 99676.pdf Unterrichtssprache:

For a counterclockwise rotation, move the Forward/Reverse Button to the right. To avoid damage to the Impact Wrench, always wait until the tool completely stops before changing rotational directions. 1/2" or 3/4” Drive Impact Head: The Impact Head features a spring and ball to securely hold a socket. Battery: The power source for the Impact Wrench is a rechargeable, 19.2 VDC Battery. Make sure to follow all safety precautions when working with the Battery. Charger: The Charger is powered by plugging the Power Plug into a 120 volt, grounded, electrical outlet. NEVER attempt to power the Charger with any other electrical source other than a 120 volt, grounded electrical outlet. To 120 Volt, Grounded, ElectricalOutlet. BatteryCharger Impact HeadTriggerForward/ReverseSwitchBatteryFIGURE ABrush Holder Cap Charging The Battery must be charged prior to the first use of the Impact Wrench.1. After first use, the Battery should only be recharged when the performance of the 2. Impact Wrench begins to diminish. Severe heat is destructive to batteries; the more heat generated, the faster the battery will lose power. A battery that gets too hot can be permanently damaged. Never discharge the battery by continuing to REV 09b pull the Trigger after the tool’s performance begins to diminish. Stop the tool, re- charge the battery, and use the fresh battery for optimal performance Do not recharge the Battery longer than 2 hours, as damage to the Battery and/or 3. Impact Wrench could occur. Depress the buttons on both sides of the Battery and pull away from the Impact 4. Wrench. Insert the Battery into the socket of the Charger. The Battery will only fit into the charger one way. Plug the Charger into the nearest 120 volt, grounded, electrical outlet. Verify that the RED Charging Indicator Light comes on. If it does not illuminate, 5. check the power connection or try a different electrical outlet. Charge the Battery for the appropriate amount of time (see Specifications chart). NOTE: When the Battery is fully charged the RED Charging Indicator Light will turn off, and the GREEN Charged Light will illuminate. While charging, the Battery and Charger may become warm to the touch. This is 6. normal and does not indicate a problem. Once the Battery is fully charged, disconnect the Charger from the electrical outlet. 7. Remove the Battery from the Charger, and insert the Battery into the handle of the Impact Wrench. NOTE: Allow the battery to cool down to room temperature before using or recharging. NOTE: To prevent accidents, move the Forward/Reverse switch to its “locked” center position after use. Clean, then store the tool indoors out of children’s reach. Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. General operating instructions Before installing an impact socket, make sure the Battery is removed from the 1. Impact Wrench to avoid accidental starting. Then, firmly insert the Socket onto the Impact Head of the tool. (See Figure A.) Always fix the workpiece securely in place, using a vise or clamps (not included).2. Insert the fully charged Battery into the handle of the Impact Wrench.3. Use the Forward/Reverse Switch to select the desired turning rotation of the Im4. pact Wrench. Insert the socket onto the nut that is to be loosened/tightened. 5. Hold the Impact Wrench firmly with both hands, as torque from the Motor will cause 6. the tool to twist. Squeeze the Trigger to turn on the Impact Wrench. When finished, release the Trigger to stop the Impact Wrench. Then, remove the 7. Battery and socket from the tool. Make sure to store the Impact Wrench in a dry, clean location out of reach of chil8. dren and other unauthorized people. Maintenance And Servicing Risk of serious personal injury from accidental starting or electric shock. Turn the Forward/Reverse Switch to the center, locked position and disconnect the Battery before performing any inspection, maintenance, or cleaning procedures. Damaged equipment can fail, causing serious personal injury. Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning and Maintenance BEFORE EACH USE,1. inspect the general condition of the tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring on the charger, and any other condition that may affect its safe operation. After Use,2. clean external surfaces of the tool with a clean cloth. WARNING! If the battery charger cord is damaged, it must be replaced only 3. by a qualified service technician. Dispose of the rechargeable NiCd battery according to State, Local and Federal 4. regulations. Contact a local recycling center for disposal directions. Replacing the Carbon Brushes It may become necessary at sometime to replace or clean the two Carbon Brushes 1. when the Mot...

Herunterladen

Geben Sie zwei Ziffern: