Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Harbor Freight Tools Dateigröße: 953.88 kb Dateiname: Unterrichtssprache:

Always insert it all the way until it locks in place with a little click. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red 4 part cannot be seen. If not, it may accidentally fall part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. • Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. Switch action CAUTION: • Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. Fig.2 To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop. Lighting up the front lamp CAUTION: • Do not look in the light or see the source of light directly. Fig.3 Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. The light automatically goes out 10 - 15 seconds after the switch trigger is released. NOTE: • Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. Reversing switch action Fig.4 This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. CAUTION: • Always check the direction of rotation before operation. • Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. • When not operating the tool, always set the reversing switch lever to the neutral position. CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing driver bit To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then release the sleeve to secure the bit. Fig.5 NOTE: • If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the bit will not be secured. In this case, try re-inserting the bit according to the instructions above. Hook (Accessory) CAUTION: • When installing the hook, tighten the screw firmly. Failure to do so may cause the breakage of the tool or personal injury. Fig.6 The hook is convenient for temporarily hanging the tool. This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool housing on either side and then secure it with a screw. To remove, loosen the screw and then take it out. Adjusting the angle head The angle head can be adjusted 360°(8 positions in 45-degree increments). To adjust it, loosen the hex bolt and remove the angle head. Adjust the angle head to the desired position and reinstall it so that the teeth on the housing will match up with the grooves in the angle head. Then tighten the hex bolt to secure the angle head. Fig.7 Fig.8 Straight head and ratchet head (Accessory) Straight heads and ratchet heads are available as optional accessories for various applications on the job. Fig.9 Fig.10 5 2. Driver bit or socket bit OPERATION Failure to use the correct size driver bit or socket N m bit will cause a reduction in the fastening torque. (kgf cm) Standard bolt 3. Bolt 50 M12 • Even though the torque coefficient and the (510) class of bolt are the same, the proper (M12) 40 Proper fastening torque Proper fastening torque fastening torque will differ according to the M10 (408) Fastening torque diameter of bolt. 30 • Even though the diameters of bolts are the (306) (M10) same, the proper fastening torque will differ M8 20 according to the torque coefficient, the class of (204) bolt and the bolt length. (M8) 4. The manner of holding the tool or the material of 10 (102) driving position to be fastened will affect the torque. 0 0123 5. Operating the tool at low speed will cause a Fastening time (S) reduction in the fastening torque. MAINTENANCE N m CAUTION: High tensile bolt (kgf cm) • Always be sure that the tool is switched off and the 40 M8 M6 (M8) (M6) 012 3 battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts. ACCESSORIES (408) Fastening torque 30 (306) 20 (204) 10 (102) 0 CAUTION: • These accessories or attachments are Fastening time (S) The proper fastening torque may differ depending upon the kind or size of the screw/bolt, the material of the workpiece to be fastened, etc. Before s...

Herunterladen

Geben Sie zwei Ziffern: