Login:
Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Anleitung Harbor Freight Tools, modell BTW200

Hersteller: Harbor Freight Tools
Dateigröße: 383.08 kb
Dateiname: 46d6e09a-9413-4f10-b42d-8f88b2a31a96.pdf
Unterrichtssprache:enesfr
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Check the torque with a torque wrench. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. 3 SYMBOLS SYMBOLS 1 The followings show the symbols used for tool. V............................volts .......................direct current .......................no load speed .../min....................revolutions or reciprocation per minute ..................number of blow IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE USC002-3 1. SAVE THESE INSTRUCTIONS; This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA rechargeable batteries marked on the charger label. Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger to rain or snow. 5. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. 6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger. 7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. 8. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a. That pins on plug of extension cord are the same number, size, and shape as those of plug on charger; b. That extension cord is properly wired and in good electrical condition; and c. That wire size is at least as large as the one specified in the table below. Table 1: RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 9. Do not operate charger with damaged cord or plug - replace them immediately. 10. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. 11. Do not disassemble charger or battery cartridge; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. 12. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. 13. The battery charger is not intended for use by young children or infirm persons without supervision. 14. Young children should be supervised to ensure that they do not play with the battery charger. 15. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 16. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge the battery cartridge when temperature is BELOW 10°C (50°F) or ABOVE 40°C (104°F) 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything to cover or clog the charger vents. 4. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. 4 (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 5. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F). 6. Do not incinerate the Battery Cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 7. Be careful not to drop or strike battery. 8. Do not charge inside a box or container of any kind. The battery must be placed in a well ventilated area during charging. SAVE THESE INSTRUCTIONS SYMBOLS The following show the symbols used for the equipment. Be sure that you understand their meaning before use. ............Ready to charge ...............Charging ...............Charging complete ...........Delay charge (Cooling) ...........Defective battery ...........Conditioning ............Cooling abnormality FUNCTIONAL DESCRIPTION CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge 002306 1 2 3 1. Red part 2. Button 3. Battery cartridge • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while sliding the button on the side of the cartridge....


Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien