Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Harbor Freight Tools Dateigröße: 638.91 kb Dateiname: 47214.pdf Unterrichtssprache:

note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. note: This air tool may be shipped with a protective plug covering the air inlet. Remove this plug before set up. air Supply tO pREVEnt SERiOuS injuRY FROm ExplOSiOn: use only clean, dry, regulated, compressed air to power this tool. Do not use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool. 1. Incorporate a filter, regulator with pressure gauge, oiler, in-line shutoff valve, and quick coupler for best service, as shown on Figure B on page 8 and Figure C on page 9. an in-line shutoff ball valve is an important safety device because it controls the air supply even if the air hose is ruptured. the shutoff valve should be a ball valve because it can be closed quickly. note: If an automatic oiler system is not used, add a few drops of Pneumatic Tool Oil to the airline connection before operation. Add a few more drops after each hour of continual use. 2. Attach an air hose to the compressor's air outlet. Connect the air hose to the air inlet of the tool. Other components, such as a coupler plug and quick coupler, will make operation more efficient, but are not required. WaRninG! tO pREVEnt SERiOuS injuRY FROm acciDEntal OpERatiOn: Do not install a female quick coupler on the tool. Such a coupler contains an air valve that will allow the air tool to retain pressure and operate accidentally after the air supply is disconnected. note: Air flow, and therefore tool performance, can be hindered by undersized air supply components. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. 3. Turn the tool's throttle or switch to the off position; refer to Operation section for description of controls. 4. Close the in-line shutoff valve between the compressor and the tool. 5. Turn on the air compressor according to the manufacturer's directions and allow it to build up pressure until it cycles off. 6. Adjust the air compressor's output regulator so that the air output is enough to properly power the tool, but the output will not exceed the tool's maximum air pressure at any time. Adjust the pressure gradually, while checking the air output gauge to set the right pressure range. 7. Inspect the air connections for leaks. Repair any leaks found. 8. If the tool will not be used at this time, turn off and detach the air supply, safely discharge any residual air pressure, and release the throttle and/or turn the switch to its off position to prevent accidental operation. note: Residual air pressure should not be present after the tool is disconnected from the air supply. However, it is a good safety measure to attempt to discharge the tool in a safe fashion after disconnecting to ensure that the tool is disconnected and not powered. maintEnancE OpERatiOnSEtup SaFEtY Item 47214 For technical questions, please call 1-800-444-3353. Page 7 Page 8 For technical questions, please call 1-800-444-3353. Item 47214 Safety Operation Maintenance Setup Figure B: Portable Air Supply Setup G A E E H B F Non-lubricated Tools Lubricated Tools B A C C D A Description Function A Air Hose Connects air to tool B Filter Prevents dirt and condensation from damaging tool or work piece C Regulator Adjusts air pressure to tool D Lubricator (optional) For air tool lubrication E Coupler and Plug Provides quick connection and release F Leader Hose (optional) Increases coupler life G Air Cleaner / Dryer (optional) Prevents water vapor from damaging work piece H Air Adjusting Valve (optional) For fine tuning airflow at tool Item 47214 For technical questions, please call 1-800-444-3353. Page 9 Maintenance Operation Setup Safety Figure C: Stationary Air Supply Setup N L L O C M C Non-lubricated Tools Lubricated Tools I H I J J K H F G E Slope F F B B A A C D Description Function A Vibration Pads For noise and vibration reduction B Anchor Bolts Secures air compressor in place C Ball Valve Isolates sections of system for maintenance D Isolation Hose For vibration reduction E Main Air Line - 3/4. minimum recommended Distributes air to branch lines F Ball Valve To drain moisture from system G Branch Air Line -1/2. minimum recommended Brings air to point of use H Air Hose Connects air to tool I Filter Prevents dirt and condensation from damaging tool or work piece J Regulator Adjusts air pressure to tool K Lubricator (optional) For air tool lubrication L Coupler and Plug Provides quick connection and release M Leader Hose (optional) Increases coupler life N Air Cleaner / Dryer (optional) Prevents water vapor from damaging work piece O Air Adjusting Valve (optional) For fine tuning airflow at tool Operating instructions Operating instructions SaFEtY SEtup OpERatiOn maintEnancE Read the EntiRE impORtant SaFEtY inFORmatiOn section at the beginning of this manual including all text under subheadings therein before...

Herunterladen

Geben Sie zwei Ziffern: