Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Grizzly Dateigröße: 2.03 mb Dateiname: a3baf946-366a-43b7-a8ea-9f789ea2f25a.pdf Unterrichtssprache:

A drill or hammer symbol will appear in line with the arrow to indicate operating mode. 1. To use the hammer-drilling mode, rotate the torque selector collar until the hammer symbol appears in line with the arrow. Apply pressure to the bit to engage the hammering mechanism. 2. To use the drilling only mode, rotate the torque selector collar until the drill symbol appears in line with the arrow. NOTE: When using carbide bits, do not use water to settle dust. Do not attempt to drill through steel reinforcing rods. Both actions will damage the carbide bits. Using Control Switch (Fig. 6, 7 and 8) The control switch may be set to three positions: forward, reverse and lock. Due to a lockout mechanism, the control switch can only be adjusted when the ON/OFF switch is not depressed. Always allow the motor to come to a complete stop before using the control switch. For forward (clockwise) rotation, push in the control switch from the right side of the tool (Fig. 6). Check the direction of rotation before use. Push in for forward Fig. 6 8 For reverse (counterclockwise) rotation, push in the control switch from the left side of the tool (Fig. 7). Check direction of rotation before use. Fig. 7 Push in for reverse To lock the trigger, push the control switch to the center position (Fig. 8). The trigger will not work while the control switch is in the center locked position. Always lock the trigger or remove the battery pack before performing maintenance, changing accessories, storing the tool and any time the tool is not in use. Fig. 8 Push to center position to lock trigger Starting, Stopping & Controlling Speed 1. To start the tool, pull the trigger. 2. To stop the tool, release the trigger and an electric brake stops the tool instantly. All models feature variable speed control. To vary the speed, simply increase or decrease pressure on the trigger. The further the trigger is pulled, the greater the speed. Drilling Set the torque selector collar to the drill position Place the bit on the work surface and apply firm pressure before starting. Too much pressure will slow the bit and reduce drilling efficiency. Too little pressure will cause the bit to slide over the work area and dull the point of the bit. If the tool begins to stall, reduce pressure slightly to allow the bit to regain speed. If the bit binds, reverse the motor to free the bit from the workpiece. APPLICATIONS WARNING! To reduce the risk of electric shock, check work area for hidden pipes and wires before drilling or driving screws. Drilling in Wood, Composition Materials and Plastic When drilling in wood, composition materials and plastic, start the drill slowly, gradually increasing speed as you drill. When drilling into wood, use wood augers or twist drill bits. Always use sharp bits. When using twist drill bits, pull the bit out of the hole frequently to clear chips from the bit flutes. To reduce the chance of splintering, back work with a piece of scrap wood. Select low speeds for plastics with a low melting point. Drilling in Metal When drilling in metal, use high speed steel twist drills or hole saws. Use a center punch to start the hole. Lubricate drill bits with cutting oil when drilling in iron or steel. Use a coolant when drilling in nonferrous metals such as copper, brass or aluminum. Back the material to prevent binding and distortion on breakthrough. Drilling in Masonry When drilling in masonry, select the hammer-drill operating mode (Cat. No. 0613-20, 0614-20, and 0624-20 only). Use high speed carbide-tipped bits. Drilling soft masonry materials such as cinder block requires little pressure. Hard materials like concrete require more pressure. A smooth, even flow of dust indicates the proper drilling rate. Do not let the bit spin in the hole without cutting. Do not use water to settle dust or to cool bit. Both actions will damage the carbide. 9 Driving Screws and Nut Running Typical Bracing Methods Drill a pilot hole when driving screws into thick or hard materials. Set the torque selector collar to the proper position and set the speed to low. Use the proper style and size screwdriver bit for the type of screw you are using. With the screwdriver bit in the screw, place the tip of the screw on the workpiece and apply firm pressure before pulling the trigger. Screws can be removed by reversing the motor. Overloading Continuous overloading may cause permanent damage to tool or battery pack. WARNING! High rotational force. To reduce the risk of injury, always hold or brace securely. Always use side handle on tools. Bit Binding A high rotational force occurs when a bit binds. If the bit binds, the tool will be forced in the opposite direction of the bit rotation. Bits may bind if they are misaligned or when they are breaking through a hole. Wood boring bits can also bind if they run into nails or knots. Be prepared for bit binding situations. To reduce the chance of bit binding: • Use sharp bits. Sharp bits are less likely to bind when drilling...

Herunterladen

Geben Sie zwei Ziffern: