Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
PRINTED IN CHINA SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It may also be used to alert against unsafe practices. This symbol is used to alert the user to useful information about proper operation of the equipment. The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. NOTICE Safety Instructions For Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of check- ing to see that keys and adjusting wrenches are removed from tool before operation. 3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 4. DO NOT USE IN DANGEROUS ENVIRONMENT. DO NOT use pneumatic tools in damp or wet locations, or where any flammable or noxious fumes may exist. Keep work area well lighted. 5. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept at a safe distance from work area. 6. MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing air hoses from tools. 7. DO NOT FORCE TOOL. It will do the job better and safer at the rate for which it was designed. 8. USE THE RIGHT TOOL. DO NOT force tool or attachment to do a job for which it was not designed. 9. DO NOT USE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. -1- H3142 Pneumatic Palm Hammer Kit Safety Instructions For Pneumatic Tools 10. USE PROPER AIR HOSE for the 18. DISCONNECT TOOLS before sertool. Make sure your air hose is in vicing and changing accessories. good condition and is long enough to 19. USE THE RECOMMENDED reach your work without stretching. ACCESSORIES. Consult the 11. WEAR PROPER APPAREL. DO owner’s manual for recommended NOT wear loose clothing, gloves, accessories. The use of improper neckties, rings, bracelets, or other accessories may cause risk of jewelry which may get caught in injury. moving parts. Non-slip footwear is 20. CHECK DAMAGED PARTS. recommended. Wear a protective Before further use of the tool, a hair covering to contain long hair. guard or other part that is damaged 12. ALWAYS USE SAFETY GLASSES. should be carefully checked to Also use a face or dust mask if cut-determine that it will operate propting operation is dusty. Everyday erly and perform its intended funceyeglasses only have impact resis-tion. Check for alignment of moving tant lenses, they are NOT safety parts, binding of moving parts, glasses. breakage of parts, mounting, and 13. WEAR APPROVED HEARING any other conditions that may affect PROTECTION. its operation. A guard or other part that is damaged should be properly 14. SECURE WORK. Use clamps or a repaired or replaced. vise to hold work when practical. It is safer than using your hand and frees 21. NEVER LEAVE UNATTENDED both hands to operate tool. TOOL CONNECTED TO AIR. Disconnect the air hose and DO 15. DO NOT OVERREACH. Keep prop- NOT leave tool until it is relieved of er footing and balance at all times. any built up pressure. 16. MAINTAIN TOOLS WITH CARE. 22. NEVER ALLOW UNTRAINED Keep tools lubricated and clean for USERS TO USE THIS TOOL best and safest performance. Follow WHILE UNSUPERVISED. instructions for lubricating and changing accessories. 23. IF YOU ARE UNSURE OF THE INTENDED OPERATION, STOP 17. REDUCE THE RISK OF UNINTENUSING THE TOOL. Seek formal TIONAL STARTING. DO NOT carry training or research books or maga tool with hand on trigger and always zines that specialize in pneumatic disconnect from air when not in use. tools. -2- H3142 Pneumatic Palm Hammer Kit Palm Hammer Safety In addition to the rules stated in the previous section, and those in the warning boxes throughout this manual, please observe the following safety tips for your pneumatic palm hammer: 1. READ THIS ENTIRE MANUAL BEFORE OPERATING THE PALM HAMMER. 2. ALWAYS DISCONNECT AIR FROM THE PALM HAMMER whenever changing tools or it may actuate accidentally and cause personal injury. 3. DO NOT SUPPORT WORKPIECE NEAR NAIL POINT OF ENTRY. Nail can deflect and be driven through the surface of the workpiece, puncturing your hand or fingers. 4. NEVER CONNECT THE PALM HAMMER TO PRESSURIZED OXYGEN OR OTHER COMBUSTIBLE GASES as a power source. Only use filtered, lubricated, and regulated compressed air. 5. ALWAYS KEEP ANY BYSTANDERS BEHIND PALM HAMMER OR AWAY FROM AREA DURING USE. Palm hammer may hit a nail at an awkward angle, which could ca...