Stimmen - 6, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
Do not use or charge batteries in hot or cold places (below 40°F (5°C) or above 105°F (40°C)). Temperature extremes reduce the ability for battery pack cells to hold a charge. Do not store batteries where the temperature may exceed 120°F (50°C), such as in a vehicle or metal building during the summer. To avoid overheating to a battery pack, allow cordless tools cool down between high torque drilling/cutting applications. The increased energy discharge rate will heat the battery pack cells faster than the cells can release the heat. This could damage the cells. After use, allow a hot battery pack to cool to room temperature before inserting it into the charger. If a hot battery is put on a charger, charging will not begin until the battery has cooled to a safe temperature. See your charger manual for more information on charging temperatures. Charging a hot battery will damage the cells. Never forcibly heat up or cool down This will damage some cells in the pack, causing them to not be able a charge. Remove the battery pack from the tool for charging when the tool can no longer perform its intended function (i.e., drilling, cutting, etc.). Leave the battery pack on the charger after it has reached a full charge; the pack will continue to receive a trickle charge to ensure capacity is maintained. Occasionally (once a week) leave the batteries on the charger overnight to help maintain cell balance. Do not store the battery on the charger (for more than 24 hours); this could reduce battery life. Never leave batteries on chargers where power interruptions are common. Damage to the battery cells could occur. Store batteries at room temperature away from moisture. Do not store in damp locations where corro sion of terminals may occur. Do not submerge your battery or cordless tools in water. This will damage the battery and tool. Charge unused batteries overnight at least every six months to maximize battery life. Unused batteries discharge at a rate of about 1% per day and will be fully discharged after six months. For batteries stored for a long time, two to ten normal charging cycles may be required before the pack is fully charged. Do not use oil or solvents to clean or lubricate your battery pack. The plastic casing will become brittle and crack, causing a risk of injury. 6 Inserting Battery Pack into Tool (Fig. 1 & 2) The battery pack may feel warm after the charging cycle. If it is warm, maximize the output of the battery by allowing it to cool for a few minutes before inserting it into the tool. Battery pack can be inserted into the tool in two ways. Fig. 1 Fig. 2 WARNING ASSEMBLY Always lock trigger or remove battery pack before changing or removing accessories. Only use accessories specifically recommended for this tool. Others may be hazardous. WARNING To reduce the risk of injury, always use a side handle when using this tool. Always brace or hold securely. Installing the Side Handle 1. To install the side handle, loosen the side handle grip until the ring is large enough to slide over the torque selector collar. The raised rib on the side handle ring fits inside the groove around the tool. Rotate the handle to the desired position and tighten the side handle until it is secure. 2. To remove the side handle, loosen the side handle grip until the ring is large enough to slide off the tool. 1. For working in restricted spaces. Insert the battery pack from the front by sliding battery pack into the body of the tool. Insert the battery pack until the battery latches lock. WARNING Charge onlyMILWAUKEE 12, 14.4 and 18 Volt battery packs in MILWAUKEE chargers. Other brands of batteries may explode causing personal injury and damage. For specifi c charging instructions, please read the operator's manual supplied with your charger. 2. For optimum weight distribution and balance. Insert the battery pack from the sliding the battery pack into the the tool. Insert the battery pack battery latches lock. 3. To remove the battery pack, press both battery latches pack off of the tool. 7 WARNING Always remove battery pack before changing or removing accessories. Only use accessories specifically recommended for this tool. Others may be hazardous. Clip-LokTM System (Fig. 3) The Clip-Lok system consists of three pieces; the belt clip, the tool holder, and the bit holder. WARNING Always remove battery pack before changing or removing accessories. Only use accessories specifically recommended for this tool. Others may be hazardous. Clip-LokTM System (Fig. 3) The Clip-Lok system consists of three pieces; the belt clip, the tool holder, and the bit holder. Bit holderFig. 3 Belt clip Tool release lever Stud Pin Clamp Clamp release Tool holder Front tangs The system is shipped assembled for right-handed use. To change the assembly for left-handed use: 1. Remove battery pack. 2. Remove screws holding the tool holder and the bit holder. 3. Lift the holders at the narrow end and pull the front tangs out of their slots. 4. Replace...