Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
This will secure the head on the column. 15. Attach the table handle to the worm drive shaft and tighten the grub screw using the 4mm hex key. 16. Fit the table lock into the table support assembly and tighten to secure the table. 17. Fit the depth scale/lock onto the handle. 18. Fit the handle and depth scale onto the motor head ensuring that the flats on the handle locate the flats on the shaft. 19. Secure the handle onto the motor head by placing the handle bolt through the middle of the handle and secure it with the 6mm hex key. 20. Fit the chuck onto the spindle and secure it by pushing it and giving it a sharp tap. Note. Ensure both surfaces are clean before putting the chuck on the spindle. 21. Place a screwdriver through the top of the pulley cover, loosen and remove the screw securing the pulley cover. Lift off the cover. 22. Fit the belts over the pulleys, refer to the inside of the cover for speed reference. Note. Fit the lower belt on first. Note. When fitting belts it is easier to place the belt onto the small pulley and then turn it onto the larger pulley. 23. To tighten the belts on the pulleys pull the motor backwards. This is best done by grabbing hold of the top of the rear pulley and the bottom of the motor housing. 24. To loosen the motor and reduce the belt tension pull the belt tension lever towards the motor and push motor forwards. 25. Replace and secure the pulley cover. Adjustments Adjusting the table height Caution. Always ensure that the drill press is switched off and the plug is removed from the power point before making any adjustments. 1. Loosen the table lock. 2. Rotate the handle in a clockwise direction to raise the table. 3. Rotate the handle in an anti-clockwise direction to lower the table. 4. Tighten the table lock to secure the table. Adjusting the table angle Caution. Always ensure that the drill press is switched off and the plug is removed from the power point before making any adjustments. 1. Loosen the screw under the table by rotating it in an anti-clockwise direction. 2. Tilt the table to the desired angle as indicated on the bevel scale. 3. Tighten the screw under the table by rotating it in a clockwise direction. Note. When the table is tilted the work piece should be clamped to the table. Extension tables Caution. Always ensure that the drill press is switched off and the plug is removed from the power point before making any adjustments. 1. The extension tables are handy when working with larger work pieces and allow the table size to be increased for greater material support. 2. To adjust the extension table loosen the 2 knobs on the underside of the work table. 3. Extend the extension table to the desired width. 4. Tighten the 2 knobs to secure the extension table in position. Tool storage drawer The tool storage drawer is handy for storing hex keys, drill bits and accessories. Installing and removing drill bits Caution. Always ensure that the drill press is switched off and the plug is removed from the power point before making any adjustments. 1. Loosen the chuck sufficiently so that the jaws are open wide enough to allow a bit to be inserted. The chuck is loosened by rotating the collar in a clockwise direction. 2. Place the bit into the open chuck as far as it will go. 3. Tighten the chuck by rotating the collar in an anti- clockwise direction. 4. To remove the bit, loosen the chuck by rotating the collar in a clockwise direction. Setting the drilling depth Caution. Always ensure that the drill press is switched off and the plug is removed from the power point before making any adjustments. 1. Loosen the handle screw half a turn using 6mm hex key 2. Ensuring the drill bit is tight in the chuck use the feed wheel to lower the spindle until the drill bit just touches the work piece. 3. Holding the handle in that position rotate the depth scale to the desired drilling depth. 4. Tighten the handle screw firmly to secure the handle in position. 5. Lift the handle up and then proceed with the drilling operation. 6. To disable the depth lock loosen the handle screw and rotate the depth scale to the maximum depth. 7. Tighten the handle screw firmly to secure the handle in position. Changing the speed Caution. Always ensure that the drill press is switched off and the plug is removed from the power point before making any adjustments. The speed of the drill press is determined by the size of the pulley steps that the belt is attached to. Using a smaller pulley step on the front pulley means a faster drill speed; using a larger pulley step on the front pulley means a slower drill speed. The below table indicates the speed of the drill in the various belt positions. 1. Remove the plug from the mains socket. 2. Take off the pulley cover. 3. Loosen the motor and reduce the belt tension by pulling the belt tension lever towards the motor and pushing motor forwards. 4. To select a faster drill speed, move the belt up to a higher step on the front and central pulleys...