Stimmen - 5, Durchschnittliche Bewertung: 4.2
(
)
)
|
Anleitung Zusammenfassung
• Do not remove battery from tool while it is running • When you charge the battery for the first time, it only accepts 80% of its maximum capacity; after several charges and discharges, however, the batteries should be at full capacity and deliver maximum performance. • Do not repeatedly recharge the battery after only a few minutes of operation; this may result in a reduction of operating time and battery efficiency. • The nickel-cadmium battery must be kept separate from the natural environment and should not be disposed of as normal domestic waste. ! Prior to disposal protect battery terminals with heavy tape to prevent short-circuit. • If you anticipate long periods of non-use for the tool, it is best to unplug the charger from its power source. ON/OFF (fig. B) • Speed control for smooth starting (fig. C). • Changing direction of rotation (fig. D). - When not properly set in left/right position, switch 1 cannot be activated. ! Change direction of rotation only when tool is at a complete standstill. • Changing bits (fig. E). - Insert the bit as deep as possible in the chuck ! Do not use bits with a damaged shank. • Torque control (VariTorque) (fig. F). - Limits the amount of output torque delivered by the chuck (16 clutch settings). - When turning in a screw, first try VariTorque position 1 and increase until the desired depth has been reached. • Holding and guiding the tool. - Keep the ventilation slots uncovered. - Do not apply too much pressure on the tool; let the tool do the work for you. Application advice • Use the appropriate bits. Select the right bit. By choosing the correct bit for every specific material, and keeping it correctly sharpened, you’ll allow your tool to show its best performance. Carbon tipped bits - wood. High speed steel bits - soft steel, aluminium, wood, etc. • When drilling ferrous metals. - Pre-drill a smaller hole, when a large hole is required. - Lubricate drill bit occasionally with oil. • When turning in a screw at/near the cross cut end or an edge of wood one should pre-drill a hole in order to avoid cracking of the wood. • For an optimal use of the tool a steady pressure on the screw is required, especially while removing. • When screwdriving in hard wood one should pre-drill a hole. Maintenace and cleaning Unplug charger from power source before cleaning. For safe and proper working, always keep the machine and the ventilation slots clean. Keep tool and charger clean. • The charger may be cleaned most effectively with compressed air (wear safety goggles). • Clean charging contacts in charger with alcohol or contact cleaner. If the machine should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an authorized after-sales service centre for Skil power tools. Important: If for any reason the moulded plug is removed from the cable of this machine it must be disposed of safely. Guarantee We guarantee Skil applicances in accordance with tatutory/ country specific regulations (proof of purchase by invoice or delivery note). Damage attributable to normal wear and tear, overload or improper handling will be excluded from the guarantee. In case of complaint please send the machine, undismantled, to your dealer or the Skil Service Center for eletric power tools. Warning! Freight and insurance costs ar charged to client, even for warranty claims. Environmental protection Recycle raw materials instead of disposing as waste. The machine, accessories and packaging should be sorted for environmental-friendly recycling. The plastic components are labelled for categorized recycling. Certificado de Garantia* 2255 (F 012 225 5..) / 2355 (F 012 235 5..) / 2455 (F 012 245 5..) Serie n. Nome do comprador Endereco Data da venda Nome do vendedor Tipo n. Nota fiscal Carimbo da firma Prescricoes de garantia 1. As ferramentas eletricas sao garantidas contra eventuais defeitos de montagem ou de fabricacao devidamente comprovados. 2. Esta garantia e valida por 12 meses, contados a partir da data de fornecimento ao usuario, sendo 3 meses o prazo de garantia legal (C.D.C) e mais 9 meses concedidos pelo fabricante. 3. Dentro do periodo de garantia, as pecas ou componentes que comprovadamente apresentarem defeitos de fabricacao, serao consertados ou (conforme o caso) substituidos gratuitamente por qualquer Oficina Autorizada Skil, contra a apresentacao do “Certificado de Garantia” preenchido e/ou da fatura respectiva. Nao estao incuidos na garantia 4. Os defeitos originados de: 4.1 uso inadequado da ferramenta (uso profissional ou industrial); 4.2 instalacoes eletricas deficientes; 4.3 ligacao da ferramenta eletrica em rede eletrica inadequada; 4.4 desgaste natural; 4.5 desgaste oriundo de intervalos muito longos entre as revisoes; 4.6 estocagem incorreta, influencia do clima, etc. Cessa a garantia 5. Se o produto for modificado ou aberto por terceiros; se tiverem sido montadas pecas fabricadas por terceiros; ou ainda, se o produto tiver sido conser...