Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
See Figure C below. Charger AdapterFigure CCordless ScrewdriverScrewdriverBitsIf any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Battery Precautions To avoid accidents, never use a different charger adapter with this tool.1. Do not expose this product to rain or wet conditions.2. To avoid damage of cable and plug, never pull the cable to disconnect the Charger 3. Adapter. Do not charge the Screwdriver if either the cable or plug are damaged.4. Repairs should be carried out by a qualified service technician only.5. Do not touch the battery poles with any conductive source.6. Note: The internal Battery Pack (22) does not come fully charged from the factory. Charge before using. REV 07a Charging the Battery Insert the Charger Adapter (24) cord plug into the unit connector as shown below.1. Plug the Charger Adapter module into an electrical outlet. The red Charging Indicator 2. on the Cordless Screwdriver will light. Charge the new battery for 10 hours. When the battery is fully charged all three LEDs will light up. Remove the Charger Adapter (24) from the electrical outlet. The red Charging indicator will turn off. See Figure D. Testing the Battery Charge Charging Adapter (24) Charging Adapter Cord Charging Indicator LEDsFront Operation Light SwitchFront Operation LightCharging Test ButtonFigure DPush the charging test button to display battery power. All three LEDs lit means the battery is fully charged. Two LEDs lit indicate that the battery is half charged. One LED lit indicates that the tool should be charged. See Figure D above. Caution: Do not overcharge the Battery. Never charge for more than 10 hours continuously. Charger Adapter should not be left plugged in after charging is complete. Operating instructions 1. Snap in the desired hex driver into the front of the Cordless Screwdriver. See Figure E below. If light is needed while driving screws, turn on the Front 2. Operation Light Switch (see Figure D for its location). The light will turn on when the Trigger Switch is on. Engage the screwdriver bit over the item being turned. 3. The bit size must match the size of the item being turned. Squeeze and hold the top part of the Trigger Switch 4. (14) to begin clockwise operation. For counterclockwise operation, squeeze the lower part of the Trigger Switch. Figure EScrewdriver BitsInsert Screwdriver Bit Here REV 07a Troubleshooting Problem Possible Cause Probable Solution Cordless Screwdriver does not operate when Trigger Switch is pressed. Battery Pack is not charged. Recharge Battery Pack. Battery Pack does not recharge after connecting Charger Adapter for hours. No power to Charger 1. Adapter. Charger Adapter defective.2. Battery Pack defective.3. Check electrical outlet for 1. power. Replace Charger Adapter.2. Replace Battery Pack.3. Maintenance When finished using the Screwdriver, place in its box along with accessories and store 1. in a clean and dry location. Recharge the Battery Pack (22) once a month. 2. Properly recycle Battery when Screwdriver reaches the end of its product life. 3. Parts List PartDescriptionQty1Output Axis12Gasket13Gearbox14Ring, Inner, Self-lock15Core, Inner, Self-lock16Block, Self-lock17Gear, Front Star18Holder, Star Gear, Middle19Gear, Star, Back110Gasket, Large111Motor Holder112Motor Gear1PartDescriptionQty13Motor114Trigger Switch115Housing (left / right)116LED Indicator117Light Cover118Light Bulb119Switch, Light120Connector Pin121PDC122Battery Pack123Charger Socket124Charger Adapter1 NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. Assembly Drawing PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack ...